X
This V4.1B bord can only be a replacement for V4.1B board, can not replace V4.0 board or other board .
pls check which board does your printer has before order . the board type will be written on the board itself .
need order a same board as your printer originally has. otherwise will not be compatible .
A4988 stepper drivers are soldered on this board.
Here are its main features:
1. Using ATMEGA2560 as its core chip, with its flash memory at 256KB and operating frequency at 16MHz.
2. Compatible with 12V/24V input voltage. Featuring dual power supply, one for powering up the heatbed (15A), the other for other electronic parts (10A).
3. The interface for the heatbed comes with a high-power MOS tube, which is of ultra-low conductive internal resistance. High performance and stable.
4. With 2 interfaces for normally open fans and 1 interface for LED light.
5. Driven by 5pcs A4988 stepper motors for dual extruders.
6. With extension interfaces for LCD display and SD card. Support 2004 and 12864 LCD display.
7. Support 3D touch auto-leveling function and filament detector.
8. Using Marlin firmware, stable and easy to operate.
9. Highly integrated and easy to assemble.
Specifications:
Net weight: 72g
Gross weight: 113g
TOP
i have the Geeetech A20T Triple Color Mixing what Marlin firmware do i need to install on a gt2560 v4.1b board or is it installed all ready
Dear customer , For questions related to printer technology, you can contact our technical supports mailbox :support@geeetech.com or create a ticket onour official website ,thanks for your consult .
My board arrived this morning I installed it correctly cable for cable powered up but the display only lit up with nothing else on the screen ,Im tried installing firmware the green light flashed but again nothing but the light on the screen.
Is it possible to update the firmware? Please take a picture of the error report on the screen when the firmware refresh fails. We need this picture to analyze the cause of the failure. Please send pictures to support@geeetech.com
I have a a10m with the gt2560 v4.1b is there any way you could update the firmware to autolevel 16 areas instead of 9 and release or link how to do so please _br_
Hi, we have not updated the firmware for the 16 point leveling yet. If you want to update the 16-point leveling, you can update it yourself, because our firmware has been open sourced.
Where do i find the files to update? and compile my own for this particulat board
https://github.com/Geeetech3D
hello ,I need to change my A 10M Motherboard to be silent stepper drivers _br_the old one is Baud:250000_br_HW Ver : GT2560 V4.1_br_FW Ver : V2.3
hello, you can order this board , but write a comment for your order , need A10M V4.1B board soldered with TMC 2208 drivers instead. instead of checking its version on screen information, pls check your control board under basement directly , to see if it is V4.1B version or not .
Does the 4.1 board have any support for silent stepper drivers?
hello, we have V4.1B board soldered with TMC 2208 drivers . if you need it , you can order V4.1B board on our website , but wrote a comment for your order , need A10M V4.1B board soldered with TMC 2208 drivers instead
Hi, I have an A10M (old model v3.0) and the Control Board is damaged. Can you help me to know if a can replace the Control Board with the new A10M Printer GT2560 V4.1B Control Board? I can use the same LCD? I need anything else to update it? thank you very much
hello , it can not use V4.0 board or V4.1B board . they still have many different parts on printer , can not do change. if your A10M is with v3.0 board , you can continue use V3.0 board . or use V3.1 board , new screen and lcd cable , so they can be compatible. A10M V3.0 board is not listed on our store , you can order this link board , but write a comment for your order, need A10M V3.0 board instead .