Difference between revisions of "Iduino Yun Cloud"

From Geeetech Wiki
Jump to: navigation, search
(Dimentions and weight)
(FAQ)
 
(4 intermediate revisions by the same user not shown)
Line 19: Line 19:
 
==Interface explanation==
 
==Interface explanation==
  
[[File:Iduino Yun Cloud -3.jpg |600px]] [[File:Iduino Yun Cloud -2.jpg |600px]]
+
[[File:Iduino Yun Cloud -3.jpg]] [[File:Iduino Yun Cloud -2.jpg]]
  
 
==Features==
 
==Features==
Line 77: Line 77:
 
*USB micro A Female: Connect to Atmega32u4, use can use it to upload sketch to Atmega32u4 or get debug info from 32u4.
 
*USB micro A Female: Connect to Atmega32u4, use can use it to upload sketch to Atmega32u4 or get debug info from 32u4.
  
[[File:Iduino Yun Cloud USB Ports.jpg|500px]]
+
[[File:Iduino Yun Cloud USB Ports.jpg|600px]]
  
 
===Buttons:===
 
===Buttons:===
 
*WLAN_RESET: Reset Linux part.see[[Iduino_Yun_Cloud#How_to_reset_Iduino_Yun.3F | here]]  
 
*WLAN_RESET: Reset Linux part.see[[Iduino_Yun_Cloud#How_to_reset_Iduino_Yun.3F | here]]  
  
[[File:Iduino Yun Cloud WLAN RESET.jpg|400px]]
+
[[File:Iduino Yun Cloud WLAN RESET.jpg|600px]]
  
 
*32u4_RSET: Reboot Atmega32u4
 
*32u4_RSET: Reboot Atmega32u4
  
[[File:Iduino Yun Cloud 32u4 RSET.jpg|400px]]
+
[[File:Iduino Yun Cloud 32u4 RSET.jpg|600px]]
  
 
*YUN_RST: Reboot Linux part
 
*YUN_RST: Reboot Linux part
  
[[File:Iduino Yun Cloud YUN RST.jpg|400px]]
+
[[File:Iduino Yun Cloud YUN RST.jpg|600px]]
  
 
<br>
 
<br>
Line 221: Line 221:
  
 
=FAQ=
 
=FAQ=
1 How to set up /www/sd and mnt/sd?  
+
'''1 How to set up /www/sd and mnt/sd?'''
  
 
The way to use /www/sd and /mnt/sd is as the same as Arduino Yun. User can prepare a USB flash and create directory /arduino and /arduino/www at the root of USB flash. Then input the USB flash into the Iduino_Yun_Shield and it will automatically create directory /www/sd and /mnt/sd, which link to /arduino and /arduino/www.
 
The way to use /www/sd and /mnt/sd is as the same as Arduino Yun. User can prepare a USB flash and create directory /arduino and /arduino/www at the root of USB flash. Then input the USB flash into the Iduino_Yun_Shield and it will automatically create directory /www/sd and /mnt/sd, which link to /arduino and /arduino/www.
  
2 What if Arduino IDE doesn’t detect Iduino Yun Shield?
+
'''2 What if Arduino IDE doesn’t detect Iduino Yun Shield?'''
  
 
You can check the below issues:
 
You can check the below issues:
Line 233: Line 233:
 
#If the Iduino Yun boots in advance than Arduino IDE, this situation may happen. So try to reboot the Iduino Yun and check again.
 
#If the Iduino Yun boots in advance than Arduino IDE, this situation may happen. So try to reboot the Iduino Yun and check again.
  
3 Where can you find the source code of the Iduino Yun?
+
'''3 Where can you find the source code of the Iduino Yun?'''
  
 
The source code can be found at https://github.com/dragino/openwrt-yun
 
The source code can be found at https://github.com/dragino/openwrt-yun
  
4 How to upload, download or edit the files in Iduino Yun?
+
'''4 How to upload, download or edit the files in Iduino Yun?'''
  
 
Iduino Yun has a built-in Linux system and supports SCP protocol. You can download or edit the Linux files using SCP tools. In Windows OS, the SCP tool is winscp. Install it and log into SCP as below:
 
Iduino Yun has a built-in Linux system and supports SCP protocol. You can download or edit the Linux files using SCP tools. In Windows OS, the SCP tool is winscp. Install it and log into SCP as below:
Line 253: Line 253:
 
[[File:How6.6 2.jpg|600px]]
 
[[File:How6.6 2.jpg|600px]]
  
5 How to reset Iduino Yun?
+
'''5 How to reset Iduino Yun?'''
  
 
Iduino Yun has a '''WLAN_RESET''' which can be used for reset. You can press the '''WLAN_RESET''' to reset the running Iduino Yun.
 
Iduino Yun has a '''WLAN_RESET''' which can be used for reset. You can press the '''WLAN_RESET''' to reset the running Iduino Yun.
Line 259: Line 259:
 
#If pressing the '''WLAN_RESET''' and release after 30 seconds, it will reset all the settings to factory default.
 
#If pressing the '''WLAN_RESET''' and release after 30 seconds, it will reset all the settings to factory default.
  
6 How to recover the Iduino Yun in case firmware crash?
+
'''6 How to recover the Iduino Yun in case firmware crash?'''
  
 
There are some cases that the Iduino Yun fails to boot. For example, upgrade an improper firmware or lost power during upgrade. But you are still able to recover the Iduino Yun by using the U-boot of IduinoYun. An instruction in Windows is shown as below:
 
There are some cases that the Iduino Yun fails to boot. For example, upgrade an improper firmware or lost power during upgrade. But you are still able to recover the Iduino Yun by using the U-boot of IduinoYun. An instruction in Windows is shown as below:
  
'''1.Turn of Windows firewall'''<br>
+
1.Turn of Windows firewall<br>
 
[[File:YUN图片1.png]]
 
[[File:YUN图片1.png]]
  
'''2.Set IP address as "192.168.255.2", Subnet mask: 255.255.255.0'''<br>
+
2.Set IP address as "192.168.255.2", Subnet mask: 255.255.255.0<br>
 
[[File:YUN图片2.png]]
 
[[File:YUN图片2.png]]
  
'''3. You need firmwares called "kernel" and "root-squash", put the firmwares and "tftpd32.exe" in same folder.'''<br>
+
3. You need firmwares called "kernel" and "root-squash", put the firmwares and "tftpd32.exe" in same folder.<br>
 
[[File:YUN图片3.png]]
 
[[File:YUN图片3.png]]
  
'''4.Connect Iduino Yun Shield to computer via cable. Power Iduino Yun Shield with 9V of DC.'''<br>
+
4.Connect Iduino Yun Shield to computer via cable. Power Iduino Yun Shield with 9V of DC.<br>
'''5.Set TPFP service:'''
+
5.Set TPFP service:
 
:(1)Open "tftpd32.exe", Choose "192.168.255.2" in "Service interfaces".<br>
 
:(1)Open "tftpd32.exe", Choose "192.168.255.2" in "Service interfaces".<br>
 
[[File:YUN图片4.png]]
 
[[File:YUN图片4.png]]
Line 285: Line 285:
 
[[File:YUN图片7.png]]
 
[[File:YUN图片7.png]]
  
'''6.Open "hercules_3-2-8.exe", set the following parameters in UDP board:'''<br>
+
6.Open "hercules_3-2-8.exe", set the following parameters in UDP board:<br>
 
:Module IP: 192.168.255.1<br>
 
:Module IP: 192.168.255.1<br>
 
:Port: 6666<br>
 
:Port: 6666<br>
Line 292: Line 292:
 
[[File:YUN图片8.png]]
 
[[File:YUN图片8.png]]
  
'''7.Back to tftpd32, click "Put":'''<br>
+
7.Back to tftpd32, click "Put":<br>
 
[[File:YUN图片9.png]]
 
[[File:YUN图片9.png]]
  
'''8.After clicking "Put", you can see "kernel" displayed in "Received data" on Hercule.'''<br>
+
8.After clicking "Put", you can see "kernel" displayed in "Received data" on Hercule.<br>
 
[[File:YUN图片10.png]]
 
[[File:YUN图片10.png]]
  
'''9.Access "Failsafe" mode: Disconnect the power supply for Iduino Yun Shield, keep pressing button "Failsafe". Then power Iduino Yun Shield again, you will see the LEDs of LAN,WLAN and SYS blinking at the same time. When these LEDs stop blinking, release "Failsafe".'''
+
9.Access "Failsafe" mode: Disconnect the power supply for Iduino Yun Shield, keep pressing button "Failsafe". Then power Iduino Yun Shield again, you will see the LEDs of LAN,WLAN and SYS blinking at the same time. When these LEDs stop blinking, release "Failsafe".
 +
 
 +
10.Send <font color="red">printenv<CR></font> command on Hercules. "Received data" will display some information from Iduino Yun Shield as follow, if not, re-send <font color="red">printenv<CR></font><br>
  
'''10.Send <font color="red">printenv<CR></font> command on Hercules. "Received data" will display some information from Iduino Yun Shield as follow, if not, re-send <font color="red">printenv<CR></font>'''<br>
 
 
[[File:YUN图片11.png]]
 
[[File:YUN图片11.png]]
  
'''11.Send the following commands in order, to upgrade kernel:'''
+
11.Send the following commands in order, to upgrade kernel:
 
  tftpboot 0x81000000 dragino2-yun-geeetech-v2.0.2-kernel.bin<CR>
 
  tftpboot 0x81000000 dragino2-yun-geeetech-v2.0.2-kernel.bin<CR>
 
[[File:YUN图片12.png]]
 
[[File:YUN图片12.png]]
Line 313: Line 314:
 
[[File:YUN图片14.png]]
 
[[File:YUN图片14.png]]
  
'''12.Disconnect the power supply for Iduino Yun Shield, and back to tftpd32, click "Break":'''<br>
+
12.Disconnect the power supply for Iduino Yun Shield, and back to tftpd32, click "Break":<br>
 
[[File:YUN图片15.png]]
 
[[File:YUN图片15.png]]
  
'''13.Change "Local File"'''<br>
+
13.Change "Local File"<br>
 
[[File:YUN图片16.png]]
 
[[File:YUN图片16.png]]
  
'''14.Choose <font color="blue">root-squashfs</font> file'''<br>
+
14.Choose <font color="blue">root-squashfs</font> file<br>
 
[[File:YUN图片17.png]]
 
[[File:YUN图片17.png]]
  
'''15.Click "Put" to send file to Hercules.'''<br>
+
15.Click "Put" to send file to Hercules.<br>
 
[[File:YUN图片18.png]]<br>
 
[[File:YUN图片18.png]]<br>
 
[[File:YUN图片19.png]]
 
[[File:YUN图片19.png]]
  
'''16. Keep pressing "Failsafe" button on Iduino Yun Shield, power Iduino Yun Shield again, you will see LEDs of LAN,WLAN and SYS blinking at the same time. When they stop blinking, release "Failsafe" button. Iduino Yun Shield is in Failsafe mode now.
+
16. Keep pressing "Failsafe" button on Iduino Yun Shield, power Iduino Yun Shield again, you will see LEDs of LAN,WLAN and SYS blinking at the same time. When they stop blinking, release "Failsafe" button. Iduino Yun Shield is in Failsafe mode now.
'''
+
 
  
'''17.Send <font color="red">printenv<CR></font> command on Hercules. "Received data" will display some information from Iduino Yun Shield as follow, if not, re-send <font color="red">printenv<CR></font>'''<br>
+
17.Send <font color="red">printenv<CR></font> command on Hercules. "Received data" will display some information from Iduino Yun Shield as follow, if not, re-send <font color="red">printenv<CR></font><br>
 
[[File:YUN图片11.png]]
 
[[File:YUN图片11.png]]
  
'''18.Send the following commands to upgrade rootfs:'''<br>
+
18.Send the following commands to upgrade rootfs:<br>
 
  tftpboot 0x81000000 dragino2-yun-geeetech-v2.0.2-rootfs-squashfs.bin<CR>
 
  tftpboot 0x81000000 dragino2-yun-geeetech-v2.0.2-rootfs-squashfs.bin<CR>
 
[[File:YUN图片21.png]]
 
[[File:YUN图片21.png]]
Line 346: Line 347:
 
[[File:YUN图片24.png]]
 
[[File:YUN图片24.png]]
  
<font color="red">Relevant file:</font><br>
+
 
 +
<font color="red">Relevant file:</font><br>  
 
http://www.geeetech.com/wiki/images/4/41/How_to_recover_Iduino_Yun_Shield.rar
 
http://www.geeetech.com/wiki/images/4/41/How_to_recover_Iduino_Yun_Shield.rar
  
 +
<font color="red">*Warning:</font>
 +
1. User should use correct address in the erase and cp.b. Wrong address may destroy the boot-loader of Iduino Yun and the device won’t boot anymore, or destroy the radio data leading to a poor Wifi performance or incorrect MAC address.
  
 +
2. Recover in Linux is similar with Windows. The different is that the tool used in Linux is nc, namely nc-kul6666. The figure below shows that the Iduino_Yun_Shield has been in Failsafe mode and detected by nc.
  
 
+
[[File:Reset firmware.png|reset firmware]]
:Warning: User should use correct address in the erase and cp.b. Wrong address may destroy the boot-loader of Iduino Yun and the device won’t boot anymore, or destroy the radio data leading to a poor Wifi performance or incorrect MAC address.
 
Recover in Linux is similar with Windows. The different is that the tool used in Linux is nc, namely nc-kul6666. The figure below shows that the Iduino_Yun_Shield has been in Failsafe mode and detected by nc.
 
 
 
[[File:Reset firmware.png|reset firmware]
 
<br>
 
<br>
 
  
 
=Reference=
 
=Reference=

Latest revision as of 09:07, 25 August 2016

Introduction

OverView

Iduino Yun cloud front.jpg Iduino Yun cloud back.JPG

Iduino Yun is a ideal IoT device for Internet of Things projetcs. It is a compatible / replacement product for Arduino Yun. It works with Arduino IDE with version higher than 1.5.4.

The Iduino Yun is a microcontroller board based on the ATmega32u4 and the Atheros AR9331. The Atheros processor supports a Linux distribution based on OpenWrt named OpenWrt-Yun. The board has built-in Ethernet and WiFi support, a USB-A port, micro-SD card slot, 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a 3 reset buttons.

Iduino Yun Bridge.png

The Iduino Yun is similar to the Arduino Leonardo in that the ATmega32u4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Yun to appear to a connected computer as a mouse and keyboard, in addition to a virtual (CDC) serial / COM port.

The Bridge library facilitates communication between the two processors, giving Arduino sketches the ability to run shell scripts, communicate with network interfaces, and receive information from the AR9331 processor. The USB host, network interfaces and SD card are not connected to the 32U4, but the AR9331, and the Bridge library also enables the Arduino to interface with those peripherals.



Interface explanation

Iduino Yun Cloud -3.jpg Iduino Yun Cloud -2.jpg

Features

  • Open source Linux (OpenWrt) onboard
  • Compatible with Arduino IDE 1.5.4 or later, user can program, debug or upload sketches to the Arduino board via the Arduino IDE.
  • Managed by Web GUI, SSH via LAN or WiFi
  • Software upgradable via network
  • Built-in web server
  • Supports internet connection via LAN port, WiFi or 3G dongle.
  • Supports USB flash to provide storage for Arduino projects.
  • Failsafe design provides robust system.



Specifications

AVR Arduino microcontroller

  • Microcontroller ATmega32U4
  • Operating Voltage 5V
  • Input Voltage 5
  • Digital I/O Pins 20
  • PWM Channels 7
  • Analog Input Pins 12
  • DC Current per I/O Pin 40 mA
  • DC Current for 3.3V Pin 50 mA
  • Flash Memory 32 KB (of which 4 KB used by bootloader)
  • SRAM 2.5 KB
  • EEPROM 1 KB
  • Clock Speed 16 MHz

Linux Microprocessor

  • Processor Atheros AR9331
  • Architecture MIPS @400MHz
  • Operating Voltage 3.3V
  • Ethernet IEEE 802.3 10/100Mbit/s
  • WiFi IEEE 802.11b/g/n
  • USB Type-A 2.0 Host
  • Card Reader Micro-SD only
  • RAM 64 MB DDR2
  • Flash Memory 16 MB

WiFi Specification

  • WiFi: Support 150M 2.4Ghz WiFi, 802.11 b/g/n
  • Frequency range: 2.4~2.4835GHz
  • Modulation: BPSK, QPSK, CCK and OFDM (BPSK/QPSK/16-QAM/ 64-QAM)
  • Sensitivity @PER: 135M : -65dBm@10%PER; 65M : -65dBm@10%PER; 54M : -68dBm@10%PER;

11M : -84dBm@8% PER; 6M : -88dBm@10% PER; 1M : -90dBm@8% PER

  • Typical Distance: Indoor: 60m (max); Outdoor 150m (max) (with 2 dBi antenna)
  • RF Power: 11n: 13dBm; 11g: 13-15dBm, 11b: 16-18dBm,
  • Connector: I-PEX connector.



USB Ports

The Iduino Yun Cloud has two USB connectors for different purpose:

  • USB Type A Female: Connect to the Linux part. it is a USB host port. User can use it to connect to USB flash, 3G dongle etc.
  • USB micro A Female: Connect to Atmega32u4, use can use it to upload sketch to Atmega32u4 or get debug info from 32u4.

Iduino Yun Cloud USB Ports.jpg

Buttons:

  • WLAN_RESET: Reset Linux part.see here

Iduino Yun Cloud WLAN RESET.jpg

  • 32u4_RSET: Reboot Atmega32u4

Iduino Yun Cloud 32u4 RSET.jpg

  • YUN_RST: Reboot Linux part

Iduino Yun Cloud YUN RST.jpg



Dimentions and weight

Iduino Yun Cloud -1.jpg

Net weight: 110g

Quick Start of Iduino Yun

This chapter shows how to run the first sketch of Iduino Yun.

Connect to Iduino Yun

Power on Iduino Yun, after the system runs, it will generate a WiFi network with SSID : I duino-A84041XXXXXX.

Iduino Yun Generate an unsecure WiFi network

Use your PC to connect to this unsecure WiFi netowrk. Your PC will get DHCP from Yun. Your PC will get an IP 192.168.240.x and the Iduino Yun will have the IP 192.168.240.1



Open Arduino IDE and configure right Profile

Open Arduino IDE and choose the profile Tools --> Boards --> Arduino Yun. Choose the ports to "Iduino at 192.168.240.1"

Choose Yun profile



Upload Bridge example

This example for the Arduino Yun shows how to use the Bridge library to access the digital and analog pins on the board through REST calls. It demonstrates how you can create your own API when using REST style calls through the browser.

Possible commands created in this shetch:

 "YUNs_IP/arduino/digital/13"     -> digitalRead(13)
 "YUNs_IP/arduino/digital/13/1"   -> digitalWrite(13, HIGH)
 "YUNs_IP/arduino/analog/2/123"   -> analogWrite(2, 123)
 "YUNs_IP/arduino/analog/2"       -> analogRead(2)
 "YUNs_IP/arduino/mode/13/input"  -> pinMode(13, INPUT)
 "YUNs_IP/arduino/mode/13/output" -> pinMode(13, OUTPUT)

In Arduino IDE, Select example File-->Examples-->Bridge-->Bridge . Click Upload , Arduino IDE will compile this example and upload to Yun. During the upload, Arduino IDE will pop up a window for asking the password. type password iduino here. and continue upload.

upload sketch to Yun





Test the sketch

After upload, user can open the web broswer and use it to Read/Write the I/Os of Yun.

type password for Bridge sketch

Notice: Yun will ask for password at the first connect via Web. The user name is root and password is iduino.

more info about this sketch please refer this link: Explain of Bridge Example



User Manual

This chapter introduce more detail for the use of Iduino Yun. Iduino Yun is compatible/replacement of Arduino Yun, user can also see the Arduino Yun manual for reference.

Getting IP address

There is a Wifi interface a LAN port on the Iduino Yun. And they both have an IP address for network connecting and device management.

Factory IP of Wifi port

IP1.png

At the first boot of Iduino Yun, an unsecure Wifi network called Iduino-xxxxxx will automatically generate. Users can use their laptop to connect to this Wifi network and the laptop will get an IP 192.168.240.xxx. The default IP of Iduino_Yun_Shield is 192.168.240.1.

FallBack IP

IP2.png

The LAN port of Iduino_Yun_Shield distributes a Fall Back IP

172.31.255.254/255.255.255.252

If the user’s laptop IP is

172.31.255.253/255.255.255.252

Then you can access Yun Shield by Fall Back IP.

Detect IP from Arduino IDE

If the Ethernet port of Iduino Yun is connected to Uplink Router or Wifi Router, the PC in the same network can use Arduino IDE to detect the IP of Iduino Yun.

Access Method

The Iduino Yun Shield runs Open Source Linux System. If you have a PC which is in the same network with Iduino Yun, you can access its system by Web or Secure Shell (SSH).

Webpage access

Use browser (recommend Firefox or Chrome) to set Iduino Yun, and you will see login page after entering 192.168.240.1.

webpage access

Default password for Iduino Yun is ‘iduino’.

SSH Access

By SSH Access, users can enter Linux system directory and customize more functions as well as applications.

SSH access

SSH Access:

IP address: IP address of Iduino_Yun_Shield
Port: 22
User Name: root
Password: iduino (default)

Webpage Setting

General setting

After login, the GUI will show the WIFI/ETH status.

General setting1.png

Click the SYSTEM button, and you can set the device password and parameter.

General setting2.png

Upgrade

You can repair bug, upgrade system, and add new function by upgrading Iduino Yun firmware through GUI. Turn to page of GUI→Upgrade and choose correct firmware. The firmware used for webpage upgrade should be Sysupgrade Type, and you can decide to save setting or not after upgrade.

upgrade

upgrade

Usually, it takes 2 minutes to upgrade firmware. The Iduino Yun will restart automatically and all the LEDs will blink together.



FAQ

1 How to set up /www/sd and mnt/sd?

The way to use /www/sd and /mnt/sd is as the same as Arduino Yun. User can prepare a USB flash and create directory /arduino and /arduino/www at the root of USB flash. Then input the USB flash into the Iduino_Yun_Shield and it will automatically create directory /www/sd and /mnt/sd, which link to /arduino and /arduino/www.

2 What if Arduino IDE doesn’t detect Iduino Yun Shield?

You can check the below issues:

  1. Whether the Arduino version is 1.5.4 or later;
  2. Whether you PC is in the same network with the Iduino_Yun_Shield;
  3. If the Iduino Yun boots in advance than Arduino IDE, this situation may happen. So try to reboot the Iduino Yun and check again.

3 Where can you find the source code of the Iduino Yun?

The source code can be found at https://github.com/dragino/openwrt-yun

4 How to upload, download or edit the files in Iduino Yun?

Iduino Yun has a built-in Linux system and supports SCP protocol. You can download or edit the Linux files using SCP tools. In Windows OS, the SCP tool is winscp. Install it and log into SCP as below:

Host name: The IP address of Iduino_Yun_Shield
User name: root
Password: iduino (default)
Protocol: SCP

How6.6 1.jpg

There will be 2 warnings during login and just ignore it. After login, a management panel will appear.

The left part of this panel is your PC’s directories and the right part is the directories of Iduino Yun. You can upload/download files by dragging, or double click the file to edit its content.

How6.6 2.jpg

5 How to reset Iduino Yun?

Iduino Yun has a WLAN_RESET which can be used for reset. You can press the WLAN_RESET to reset the running Iduino Yun.

  1. If pressing the WLAN_RESET and release after 5 seconds, it will reset the Wifi setting and other settings will be kept.
  2. If pressing the WLAN_RESET and release after 30 seconds, it will reset all the settings to factory default.

6 How to recover the Iduino Yun in case firmware crash?

There are some cases that the Iduino Yun fails to boot. For example, upgrade an improper firmware or lost power during upgrade. But you are still able to recover the Iduino Yun by using the U-boot of IduinoYun. An instruction in Windows is shown as below:

1.Turn of Windows firewall
YUN图片1.png

2.Set IP address as "192.168.255.2", Subnet mask: 255.255.255.0
YUN图片2.png

3. You need firmwares called "kernel" and "root-squash", put the firmwares and "tftpd32.exe" in same folder.
YUN图片3.png

4.Connect Iduino Yun Shield to computer via cable. Power Iduino Yun Shield with 9V of DC.
5.Set TPFP service:

(1)Open "tftpd32.exe", Choose "192.168.255.2" in "Service interfaces".

YUN图片4.png

(2)Host: 192.168.255.2
Port:6666

YUN图片5.png

(3)Choose file "kernel" in "Local File".

YUN图片6.png
YUN图片7.png

6.Open "hercules_3-2-8.exe", set the following parameters in UDP board:

Module IP: 192.168.255.1
Port: 6666
Local Port: 6666

Click "Listen":
YUN图片8.png

7.Back to tftpd32, click "Put":
YUN图片9.png

8.After clicking "Put", you can see "kernel" displayed in "Received data" on Hercule.
YUN图片10.png

9.Access "Failsafe" mode: Disconnect the power supply for Iduino Yun Shield, keep pressing button "Failsafe". Then power Iduino Yun Shield again, you will see the LEDs of LAN,WLAN and SYS blinking at the same time. When these LEDs stop blinking, release "Failsafe".

10.Send printenv<CR> command on Hercules. "Received data" will display some information from Iduino Yun Shield as follow, if not, re-send printenv<CR>

YUN图片11.png

11.Send the following commands in order, to upgrade kernel:

tftpboot 0x81000000 dragino2-yun-geeetech-v2.0.2-kernel.bin<CR>

YUN图片12.png

erase 0x9fea0000 +0x140000<CR>

YUN图片13.png

cp.b 0x81000000 0x9fea0000 $$filesize<CR>

YUN图片14.png

12.Disconnect the power supply for Iduino Yun Shield, and back to tftpd32, click "Break":
YUN图片15.png

13.Change "Local File"
YUN图片16.png

14.Choose root-squashfs file
YUN图片17.png

15.Click "Put" to send file to Hercules.
YUN图片18.png
YUN图片19.png

16. Keep pressing "Failsafe" button on Iduino Yun Shield, power Iduino Yun Shield again, you will see LEDs of LAN,WLAN and SYS blinking at the same time. When they stop blinking, release "Failsafe" button. Iduino Yun Shield is in Failsafe mode now.


17.Send printenv<CR> command on Hercules. "Received data" will display some information from Iduino Yun Shield as follow, if not, re-send printenv<CR>
YUN图片11.png

18.Send the following commands to upgrade rootfs:

tftpboot 0x81000000 dragino2-yun-geeetech-v2.0.2-rootfs-squashfs.bin<CR>

YUN图片21.png

erase 0x9f050000 +0xe50000<CR>

YUN图片22.png

cp.b 0x81000000 0x9f050000 $$filesize<CR>

YUN图片23.png

19.Send the following command to reset Iduino Yun Shield.

reset<CR>

YUN图片24.png


Relevant file:
http://www.geeetech.com/wiki/images/4/41/How_to_recover_Iduino_Yun_Shield.rar

*Warning: 1. User should use correct address in the erase and cp.b. Wrong address may destroy the boot-loader of Iduino Yun and the device won’t boot anymore, or destroy the radio data leading to a poor Wifi performance or incorrect MAC address.

2. Recover in Linux is similar with Windows. The different is that the tool used in Linux is nc, namely nc-kul6666. The figure below shows that the Iduino_Yun_Shield has been in Failsafe mode and detected by nc.

reset firmware

Reference