Update log:
1. A 3-pin straight pin is added to connect with 3D touch auto leveling sensor.
2. The USB connector will not provide 5V for the board, if you need to refresh the firmware, please provide external power supply.
3. The power port has been changed from hollow to solid one to provide higher current-carrying capability.
4. The three heater connecter has been changed into blue ones: 2-pin RC301 5.0mm 15A
Can i buy from you the fuse LF15A for this motherboard?_br_
Unfortunately, we don't sell it separately.
Does it work for an A10M with a Gt2560 V3.1 motherboard?
Thanks for your support to geeetech. I regret to tell you that they are not suitable.
Is this board suitable for Geeeteck P i3 B printer ?. In this case, has this boarb the firmware uploaded.
hello, yes, it is suitable for PRO B printer. yes, it will comewith firmware pre uploaded.
Hello, I want to buy this control board to build a 3 axis system. Can you please suggest me the power supply that would work with this control board? thanks.
hello, may i know which model printer do you have, can you help send details to sales@geeetech.com
is this the stock board used in your a10m printer?will this work as an upgrade to a printer with 24v like tevo tornado
A10M use V3 board, SKU 700-0001-1109. We do not test it on other machine, so i am not sure of it, thanks
Can i buy this kit and just plug it straight into a CTC Pro B DIY 3D printer?
yes, it can use it
My problem is someone can give me the solution video to me
hello can u tell more details to me? by the way, please send mails to jocelin.jia@geeetech.ch, thanks
will this work on ctc diy without firmware flash (i3 pro b.)
hello, if you want to buy the board without firmware, please make a comment when you buy it, we make a special for you.
Hello. Can somone tell me why the GT2560 on the PWM_FAN keep on cooling when I set the speed to 0? Is it normal?
Hi Stefano ,which fan you used ? Is there 3 pins ? Which software you used ? controlled by repetier host?
Can this board replace the GT2560revB board using the same Marlin firmware for the MeCreator2?
Hi Tony ,this is the GT256 revA ,when you place the order you can remark to the sales that the board need to be used on Me creator2 printer and she will arrange it ,any problem pls kindly let me know.
I have this board installed on my Prusa I3 ProB and I tried several fans with pwm capability but no way to reduce or control the fan spins. Everything else works just fine but I need absolutely the cooling fan software controlled. Please help. Regards Danilo
Hi Danilo,You can email your problem by details to our technican:technical@geeetech.com and ask him for help.
Hi, I have the printer Geeetech Prusa I 3 aluminium. I buy this board with 3D Touch. What firmware i must load on this board ?
Hi Ghislain,you should use the same firmware on the printer .
I have just purchased a ctc prusa i3 with the gt2560 Rev A. The problem is that it doesn't come with the ability to upgrade or change firmware without a lot of effort. Does this new board come with the ability to change the firmware simply by using the ardunio loader?
Hi Ron,the board uses the ardunio loader ,could you shoot what wrong for the board to our technican to check :technical@geeetech.com?
Binary sketch size: 82,670 bytes (of a 258,048 byte maximum) avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_ReceiveMessage(): timeout avrdude: stk500v2_getsync(): timeout communicating with programmer This it the time out reading i get when I try updating firmware to my gt2560. Help? Ron
Hello Ron,pls email to our technican for help:technical@geeetech.com
I have the Aluminum I3 and want to upgrade to GT2560. What do I need to complete this? LCD, cables, connectors??? I have emailed Sales twice with no response.
Hi Mike ,pls email to our technican for help:technical@geeetech.com
hi do you have this board 3d touch ready as have bad eyes and have problem see that small to solder
Hello Alan, please do not worry, this new version has extra pins for the 3Dtouch, no soldering is needed any more.
Friends: Is there a 5 volt output on the gt 2560 map of the delta geeetech?
Hi,there is a "5V" spot near the mainchip on the board.
Hi! How can i connect external drivers to this card to drive bigger steppers such as NEMA 23 425 oz 3A? Needs something extra or so? Thank you!
Do you have updated firmware for the I3 Pro C Dual extruder for this board?
for the latest firmware of pro C, please download here http://www.geeetech.com/forum/download/file.php?id=1555
Hi,i have Prua i3 pro C Dual extruder and i want add Diamond Hotend. the controller board GT2560 permit to add anoter stepper motor
sorry, this board can only support 2 extruders. You can use Rumba http://www.geeetech.com/geeetech-rumba-3d-printer-controller-board-p-848.html, which support 3 extruders
Can you adjust the voltage to the PWM for a cooling fan at the moment it's only 10.5 volts
You need to adjust the voltage of the power supply to adjust the voltage of the fan
I have a prusa i3 pro B (I think it was called Euro something), and I have a fuse (for the bed) not working. I replaced the fuse with other similar, but it looks tike the fuse holder is screwed. It works, but from time to time I have to push it. I want to replace the board, and if if there is a better board I would like to get it, as I don't want to deal with this things,
Traduttore ITALIANO INGLESE Good morning , I wanted to know if the 3D GT2560 card can be mounted on a Prusa i3 m201?
yes, it can be used on M201, but there will be no Mixer feature for the printer.
What power supply I need for a makerbot type 3d printer with 24v dual extruder and 300 x 200 24v heat bed ? Do I need to purchase 2 power supplies or one ? I'm confuse and new in all this.
Hi you can contact this e-mail technical@geeetech.com for technical support. Thank you.
I also want to know what is the output voltage for the steeper motor if my power supply is 24v ? because 24v nema 17 look hard to find and are expensive compare to standard one.
hey there, i would like to connect a 24v heat bed to this board and use a 24v supply, also my 2 Z axis motors can run on 24v but the rest need 12v. do you have to declare this in the firmware or is it not possible to have 12v for some components and 24v for other components
Hello Evan, you can connect a 24V heat bed, but the motors must have the same voltage.
Why 5 drivers? Only 3 slots visible.
Hello George, these 5 drivers are for A4988,and they respectively drive the X axis,Y axis and Z axis and two extruders.