Page 3 of 4

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Wed Mar 25, 2020 12:54 am
by Matsubaa
It was overkill for just the printer but this is the exact kit I bought: https://www.amazon.com/gp/product/B01MC ... UTF8&psc=1

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Wed Mar 25, 2020 9:35 pm
by axiom
Matsubaa wrote:
Wed Mar 25, 2020 12:54 am
It was overkill for just the printer but this is the exact kit I bought: https://www.amazon.com/gp/product/B01MC ... UTF8&psc=1
Nice! Thank you!

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Sat Apr 25, 2020 6:09 am
by t2u
Hello everybody,
I would like to know if it would be possible to have photos, a diagram, or a detailed explanation of the new connection because I am a little lost with the wiring of the hotend part (extension card).
Thank you in advance for your help.

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Sat Apr 25, 2020 11:42 am
by William
Hi,do you mean this?
转接板介绍.png
转接板介绍.png (305.75 KiB) Viewed 10190 times
转接板的3d touch接法.JPG
转接板的3d touch接法.JPG (130.74 KiB) Viewed 10190 times
3d touch 接法.png
3d touch 接法.png (398.84 KiB) Viewed 10190 times

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Sat Apr 25, 2020 9:48 pm
by t2u
yes the extension card in photo.
I would like to know how to connect the extension card to the skr1.3

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Sat Apr 25, 2020 9:51 pm
by t2u
yes the extension card in photo

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Sun Apr 26, 2020 5:09 am
by t2u
Matsubaa wrote:
Mon Nov 25, 2019 9:55 pm
Using the below images, I cut the connector off the control-board end of the hotend bundle.

I'm don't have the 3d touch connected yet but I've confirmed I've got motion control, heating and fans.

I've crimped on JST connectors for leads that needed them.
Pin -> Board Connection
6 -> I
7 -> H
8 -> D
9 -> H
10 -> D
11 -> C
12 -> C


it is this part that I do not understand very well, that is why I would have liked more detail on the wiring

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Fri May 15, 2020 5:52 pm
by andresdrb
HI There,

I´m going to do the same mod to my printer (to my A20 actually, but should be the same). COuld someone let me know which jumpers you left where? On this video (https://www.youtube.com/watch?v=GNGN2iSQ5j4&t=866s) they mention to initially remove all jumpers for the drivers and go from there (I know my way around with that) but mentions also other jumpers but I´m not clear which I should leave where. Can you help? I donñt want to burn the board or do something wrong. ANy closeup pictures of the biard wuld help to see which jumper is where.

Cheers

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Thu May 28, 2020 8:16 pm
by derekpittx
I have an SKR 1.3 on the way, arriving Monday since it was actually cheaper to upgrade than to replace. I'll probably step up to the TMC2130's at some later date but for now it's just a straight-up replacement of the GT2560 v3 I'm after.

Re: SKR V1.3 on the A10 - Any pointers?

Posted: Tue Jun 30, 2020 6:35 pm
by Trust35
Hi! I have installed SKR 1.4. all is ok but i dont't know how connect th eextruder motor In motor is 4 cables black,red,green and blue. How is conneced on SKR? THANK you very much!!