Texture very bad at rear part of build

TonyEng
Posts: 2
Joined: Sun Oct 14, 2018 9:26 am

Texture very bad at rear part of build

Post by TonyEng » Fri Feb 07, 2020 5:28 pm

My Mecreator2 over a couple of years has printed may very wonderful prints wth very good quality but recently it gradually needed new bearings as the texture degraded so I changed the X and Y bearings. But now the front apprimately half of the build area produces a reasonable good print quality but the back part is very bad. Some layers are shifted back on the Y axis by upto about 1mm and some are ok, making it very rough. I have reduced the accelerations and jerks to a minimum and am printing with PLA at 50mm/sec with a travel of only 30mm/s. Have retraction of 5.0mm with -0.5mm restart.

Any ideas are welcome :)
Attachments
Bad texture at rear.JPG
Bad texture at rear.JPG (288.38 KiB) Viewed 25237 times

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: Texture very bad at rear part of build

Post by William » Sat Feb 08, 2020 8:36 am

Hi,regarding the problem of layer shift, you can check the tightness of the belt; whether the bearing has the proper lubricant; whether the drive plate voltage is 0.8-1.2V.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

TonyEng
Posts: 2
Joined: Sun Oct 14, 2018 9:26 am

Re: Texture very bad at rear part of build

Post by TonyEng » Mon Feb 10, 2020 7:26 am

Thanks William for your fast response and great suggestions.

I am assuming the voltage and lubricant are fine as the front half prints without layer shifting. The bed is 160mmx160mm - only the front 50-80mm works without layer shifting. I thought it might have been due to alignment of the belts but I have check and I think I have these very well aligned. The belts are very tight and held in tension by small clips that came with the print and I have added a belt tensioner holder I printed from Thingiverse.

Although I have been very careful when I take it apart and the rods all seem very straight - I have rolled them on a table and can't see light though at any time.

Regarding the blobs, I have a lot of retraction, but will increase this and if no improvement, I will try and change the feed.

regards
tony

camilasmith934
Posts: 14
Joined: Thu Oct 29, 2020 6:14 pm

Re: Texture very bad at rear part of build

Post by camilasmith934 » Thu Oct 29, 2020 6:15 pm

Get the very easiest & simple way to book your Flight Tickets at Delta Airlines Reservations, our customer service 24*7 available for customer support, you can easily book your flight tickets by visiting our website.

camilasmith934
Posts: 14
Joined: Thu Oct 29, 2020 6:14 pm

Re: Texture very bad at rear part of build

Post by camilasmith934 » Wed Nov 11, 2020 2:41 pm

Book your flight tickets at Allegiant Airlines Flight Reservations, we provide ultimate discount on flight tickets booking.

camilasmith934
Posts: 14
Joined: Thu Oct 29, 2020 6:14 pm

Re: Texture very bad at rear part of build

Post by camilasmith934 » Tue Dec 08, 2020 3:33 pm

<a href="https://clinkergram.com/blogs/5927/What ... >Allegiant Airlines Flight Reservations</a>
<a href="https://www.click4r.com/posts/g/2383816 ... >Allegiant Airlines Reservations</a>
<a href="https://www.smore.com/9vtka-pet-strateg ... >Allegiant Airlines Phone Number</a>
<a href="https://latamairlinesreservations.wordp ... >Allegiant Airlines Reservation Number</a>
<a href="https://justpaste.it/8yd13">Allegiant Airlines Booking Number</a>
<a href="https://www.linkedin.com/pulse/allegian ... >Allegiant Airlines Flight Reservations</a>
<a href="https://camilasmith934.tumblr.com/post/ ... >Allegiant Airlines Reservations</a>
<a href="https://www.reddit.com/user/camilasmith ... >Allegiant Airlines Phone Number</a>
<a href="https://rewardbloggers.com/blog/post/15 ... >Allegiant Airlines Reservation Number</a>
<a href="https://sites.google.com/view/allegiant ... >Allegiant Airlines Booking Number</a>
<a href="https://www.800customernumber.net/airli ... >Allegiant Airlines Booking Number</a>
<a href="https://www.eranewblog.com/travel/alleg ... >Allegiant Airlines Phone Number</a>





Post Reply