Auto Bed Levelling on M201 ?

nazario
Posts: 4
Joined: Tue Feb 09, 2016 12:56 am

Auto Bed Levelling on M201 ?

Post by nazario » Sat Mar 12, 2016 8:35 am

May I instal an auto bed levelling on my M201 ?
Hardware and Firmware support this feature ?
Tnks

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: Auto Bed Levelling on M201 ?

Post by Mark » Sat Mar 12, 2016 10:45 am

the hardware, I think you can connect the sensor to the endstop connectors, but there's no firmware to use, the firmware is not open sourced..

nazario
Posts: 4
Joined: Tue Feb 09, 2016 12:56 am

Re: Auto Bed Levelling on M201 ?

Post by nazario » Sun Mar 13, 2016 6:09 am

And is possible to use an other open source firmware on this printer (Repetier) ?
I want replace the extruder 2in1out with a one or two single extruder because I have had many problems with the extruder of the M201. Is this possible ?
Many tnks

Nazario

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: Auto Bed Levelling on M201 ?

Post by Mark » Tue Mar 15, 2016 4:04 pm

I have a firmware here, you can upgrade the M201 to a dual extruder printer like I3 pro C, just buy a MK8 dual extruder and replace the 2-in-1-out extruder, but note that your power supply for the GTM32 board is 24V, you might need to buy two 24V heaters for the dual extruder.
GTM32_DUAL.zip
(97.33 KiB) Downloaded 458 times

nazario
Posts: 4
Joined: Tue Feb 09, 2016 12:56 am

Re: Auto Bed Levelling on M201 ?

Post by nazario » Thu Mar 17, 2016 5:37 pm

Many tnks Mark
I will try this firmware

syossi2
Posts: 73
Joined: Sun Apr 03, 2016 4:00 pm

Re: Auto Bed Levelling on M201 ?

Post by syossi2 » Tue Dec 06, 2016 10:00 pm

hi

Can geeetech update the old firmware of this dual for m201 so it match to the new 1.0.5 ? with the new stepping?


thanks
yossi
printing 3D with M201 Geeetech

Benni94
Posts: 10
Joined: Tue May 31, 2016 1:03 am

Re: Auto Bed Levelling on M201 ?

Post by Benni94 » Wed Dec 07, 2016 3:29 pm

I want it too!

daveapplemotors
Posts: 76
Joined: Tue Aug 16, 2016 11:36 pm

Re: Auto Bed Levelling on M201 ?

Post by daveapplemotors » Fri Mar 10, 2017 7:18 am

I downloaded GTM32_DUAL.zip that someone kindly uploaded but it is an exe file.

Does an and anyone have ABL and two extruders working? I have converted my Geeetech Prusa i3 pro A to a dual extruder machine but ABL dosen't work.

claytonc2001
Posts: 0
Joined: Fri Oct 06, 2017 12:26 am

Firmware for GTM32 Rev A board installation

Post by claytonc2001 » Fri Oct 06, 2017 12:33 am

I had this firmware installed and working. However, I stupidly shorted some wires and had to get a replacement. My original board was a rev B. They sent me a rev A as a replacement board for $50. The problem is that this REV A board does not have the jumpers on it to allow me to flash the GTM32_DUAL firmware to it. From what I read there is a sort of adapter I would have to get to program the board.... Is the REV A board a step backward? Is there a way around this way of updating the board?

User avatar
William
Site Admin
Posts: 6338
Joined: Tue Jun 07, 2016 9:38 am

Re: Auto Bed Levelling on M201 ?

Post by William » Fri Oct 06, 2017 2:36 pm

As far as I know, you should use the ST-LINK to upload.
viewtopic.php?f=20&t=17173
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Post Reply