I want my Mecreator2 back

Post Reply
rabe
Posts: 4
Joined: Fri Jun 16, 2017 12:06 am

I want my Mecreator2 back

Post by rabe » Fri Jun 16, 2017 5:27 am

The last five month my Mecreator2 worked without any problem. Today I switched it on and on the display are shown two lines with blocks. The whole day I searched the net to get the printer run, but nothing helped - but I really have no idea about it.

After all I think the GT2650 Rev B board might be defect, but I do not find a shop, where it is sold.

User avatar
William
Site Admin
Posts: 4465
Joined: Tue Jun 07, 2016 9:38 am

Re: I want my Mecreator2 back

Post by William » Fri Jun 16, 2017 8:41 am

Hi,as to LCD issue,here is a related post you can refer to:http://www.geeetech.com/forum/viewtopic ... 23&t=17040
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

rabe
Posts: 4
Joined: Fri Jun 16, 2017 12:06 am

Re: I want my Mecreator2 back

Post by rabe » Fri Jun 16, 2017 11:42 pm

Many thanks for Your fast answer William. After trying around for several hours I don't think it is an LCD issue. Since two days I cannot connect the printer to Simplify3D and it worked fine before.

I thought to try to play new firmware on the printer and tried to connect the GT2560 Rev B to the Arduino IDE and get the message "unknown board". Some other Arduinos work fine mit my mac.

Is there any way for me to check if the GT2560 is okay?




Bildschirmfoto 2017-06-16 um 14.26.41.png
Bildschirmfoto 2017-06-16 um 14.26.41.png (50.97 KiB) Viewed 3810 times
Bildschirmfoto 2017-06-16 um 14.27.09.png
Bildschirmfoto 2017-06-16 um 14.27.09.png (19.79 KiB) Viewed 3810 times

User avatar
William
Site Admin
Posts: 4465
Joined: Tue Jun 07, 2016 9:38 am

Re: I want my Mecreator2 back

Post by William » Sat Jun 17, 2017 9:12 am

Could you send some pictures which the control board is power on?
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

rabe
Posts: 4
Joined: Fri Jun 16, 2017 12:06 am

Re: I want my Mecreator2 back

Post by rabe » Sat Jun 17, 2017 6:29 pm

Here it is. One of my problems is that I don't find the GT2560 Rev B documented or sold anywhere. Thank You for Your answers.

board.jpg
board.jpg (544.44 KiB) Viewed 3771 times

rabe
Posts: 4
Joined: Fri Jun 16, 2017 12:06 am

Re: I want my Mecreator2 back

Post by rabe » Tue Jun 20, 2017 8:24 am

Does anyone know, if it is correkt, when this three LED are shining?

User avatar
William
Site Admin
Posts: 4465
Joined: Tue Jun 07, 2016 9:38 am

Re: I want my Mecreator2 back

Post by William » Thu Jun 22, 2017 6:03 pm

rabe wrote:
Tue Jun 20, 2017 8:24 am
Does anyone know, if it is correct when this three LED are shining?
The three LED lighting show the necessary power 12V,5V is fine so that the control board can work properly.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests