Absolutely desperate

otibook
Posts: 46
Joined: Thu Jul 23, 2015 12:47 am
Location: Madrid, Spain

Re: Absolutely desperate

Post by otibook » Wed Apr 05, 2017 6:20 am

I see. No solution for my printer... :twisted:

User avatar
William
Site Admin
Posts: 4466
Joined: Tue Jun 07, 2016 9:38 am

Re: Absolutely desperate

Post by William » Wed Apr 05, 2017 5:45 pm

Hi,could you send some videos to show the details of your problems as much as possible?
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

otibook
Posts: 46
Joined: Thu Jul 23, 2015 12:47 am
Location: Madrid, Spain

Re: Absolutely desperate

Post by otibook » Wed Apr 05, 2017 7:56 pm

Of course, tonight I'll upload video.

otibook
Posts: 46
Joined: Thu Jul 23, 2015 12:47 am
Location: Madrid, Spain

Re: Absolutely desperate

Post by otibook » Thu Apr 06, 2017 8:41 am

Hello
Those are the videos
1- Autoleveling. Ear the "cracks" of the pulleys
2 Triying to print PSU case from thingiverse

Thank You.

I am sorry but I have tried to upload the videos on AVI, MPEG, M4V, MOV formats and always get the message "The extension XXX is not allowed

otibook
Posts: 46
Joined: Thu Jul 23, 2015 12:47 am
Location: Madrid, Spain

Re: Absolutely desperate

Post by otibook » Thu Apr 06, 2017 4:22 pm


User avatar
William
Site Admin
Posts: 4466
Joined: Tue Jun 07, 2016 9:38 am

Re: Absolutely desperate

Post by William » Fri Apr 07, 2017 2:10 pm

Hi,after watching your videos,I have some tips for you. :)
First of all, you can check whether the XYZ axis can move up and down smoothly, because I found that the z-axis may be stuck based on your video and you can use the lubricants(WD 40) to make it smoother when necessary.
Besides,Please check the A4988 voltage of each axises on your motherboard, you can increase the resistance of the potentiometer to increase the motor drive, as shown in the picture:Image;Image.
Thridly,It will be better if you can re-leveling your printer according to the following video:https://www.youtube.com/watch?v=VCa_Bvx ... o1VV2ioejQ.
After the above measures if it still don't work ,there maybe some problems in your firmware.Please reinstall it and you can download the lastest one in this post:viewtopic.php?f=20&t=17046.Please take a check.
Finally,please feel freely to tell me your latest situation If you still can not solve it.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

otibook
Posts: 46
Joined: Thu Jul 23, 2015 12:47 am
Location: Madrid, Spain

Re: Absolutely desperate

Post by otibook » Fri Apr 07, 2017 4:19 pm

Thank You very much.

I am using lithium grease to on the rails and bearing. It goes super smooth.
I will measure the voltage and adjust it this weekend.

otibook
Posts: 46
Joined: Thu Jul 23, 2015 12:47 am
Location: Madrid, Spain

Re: Absolutely desperate

Post by otibook » Sun Apr 09, 2017 2:36 am

I have adjust the voltage of the drivers to 1 volt and I have noticed a little improve but the cracks of the pulleys still are there. I'm sending a new video trying to print PSU case.
At least now I can print little pieces without problems but the quality is quite poor. See the attached photo.
Attachments
IMG_0935.jpg
IMG_0935.jpg (1.75 MiB) Viewed 4371 times

otibook
Posts: 46
Joined: Thu Jul 23, 2015 12:47 am
Location: Madrid, Spain

Re: Absolutely desperate

Post by otibook » Sun Apr 09, 2017 2:45 am


otibook
Posts: 46
Joined: Thu Jul 23, 2015 12:47 am
Location: Madrid, Spain

Re: Absolutely desperate

Post by otibook » Mon Jun 12, 2017 5:43 am

Just two months waiting for any helming. Pleaseeeeee HEEELLLLLPPPP!!!!!!

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests