How to slove the problem of MAX/MIN TEMP error(GT2560)

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by Mark » Thu Oct 08, 2015 5:36 pm

Hi guys, if your printer shows MAX/MIN TEMP error on the LCD, don't worry, you can refer to the following information to check it, good luck :D
LCD:ERROR:MAX TEMP OR ERROR:MIN TEMP
01 MAX MIN TEMP.jpg
01
01 MAX MIN TEMP.jpg (90.18 KiB) Viewed 80076 times
Above of all,check the wiring of thermistors if you have a single extruder on your printer.The right one should be like this:
QQ图片20170217115552.jpg
QQ图片20170217115552.jpg (44.64 KiB) Viewed 73845 times
Recommended solutions:
1.1 First, check the motherboard. If you get 0℃ and 358 ℃ when you make the thermistor open circuit or short, then the board is good. You can do it as follows.

Note: If your printer is Delta G2/G2S series, before checking this please install the firmware for I3X or I3 pro C, cause when you short out the thermistors with the firmware of G2/G2S, it will always show 0 degrees on the LCD, though it is exactly MAX temp error.

Open circuit:
open circuit01.jpg
open circuit01
open circuit01.jpg (200.95 KiB) Viewed 80076 times
open circuit02.jpg
open circuit02
open circuit02.jpg (102.59 KiB) Viewed 80076 times
Short the board:
short01.jpg
short01
short01.jpg (213.81 KiB) Viewed 80076 times
short02.jpg
short02
short02.jpg (120.47 KiB) Viewed 80076 times
For example,the T_HE2 is shorted out.As a result,the second extruder will always display 358/0 no matter you make it open circuit or short circuit.
TH2.jpg
TH2.jpg (177.63 KiB) Viewed 79691 times
1.2 If the board is OK, please check if somewhere of the wire are connected or not.
For example, the thermistor is shorted out as the picture shows:
05.jpg
05
05.jpg (147.8 KiB) Viewed 80077 times
If so, the current will not go through thermistor, and LCD will display TEMP ERROR. You can refer to the following information:
MAXTEMP ERROR:
1.2.1 If it shows "358/0, room temp/0; Err: MAXTEMP". The extruder thermistor is short.
1.2.2 If it shows "358/0, 358/0; Err: MAXTEMP". Both extruder thermistor and hot bed thermistor are short.
1.2.3 If it shows "room temp/0, 358/0; Err: MAXTEMP BED". The hot bed thermistor is short.
MINTEMP ERROR:
1.2.4 If it shows "0/0,room temp/0; Err: MINTEMP". The extruder thermistor is open circuit.
1.2.5 If it shows "0/0, 0/0; Err: MINTEMP". Both extruder thermistor and hot bed thermistor are open circuit.
1.2.6 If it shows "room temp/0, 0/0; Err:MINTEMP BED". The hot bed thermistor is open circuit.

NOTE: Remember to reset the LCD after you do those experiments. And the MAXTEMP shows in the LCD is not always 385, it’s between 358 and the temperature you set in the firmware here:

#define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275
#define HEATER_2_MAXTEMP 275
#define BED_MAXTEMP 150

1.3 If one of your thermistor is working, you can swap it with the TEMP ERROR one, and see if the thermistor is dead or not.

Hope this will help you guys, thanks!

terrapetros
Posts: 4
Joined: Tue Feb 21, 2017 7:19 am

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by terrapetros » Fri Feb 24, 2017 5:18 am

16931111_1333760520018720_1462600160_o.jpg
16931111_1333760520018720_1462600160_o.jpg (117.28 KiB) Viewed 73662 times
16930743_1333760493352056_1930548186_o.jpg
16930743_1333760493352056_1930548186_o.jpg (74.18 KiB) Viewed 73662 times
16910686_1333760466685392_914867089_o.jpg
16910686_1333760466685392_914867089_o.jpg (105 KiB) Viewed 73662 times

hi guys,

i am having the same mintemp problem and i think that is everything good connected. on my lcd display it only shows "0/0,room temp/0; Err: MINTEMP".

is something wrong on the pictures ?

thanks

bang
Posts: 402
Joined: Wed Dec 28, 2016 2:12 pm

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by bang » Fri Feb 24, 2017 2:03 pm

terrapetros wrote:
16931111_1333760520018720_1462600160_o.jpg
16930743_1333760493352056_1930548186_o.jpg
16910686_1333760466685392_914867089_o.jpg

hi guys,

i am having the same mintemp problem and i think that is everything good connected. on my lcd display it only shows "0/0,room temp/0; Err: MINTEMP".

is something wrong on the pictures ?

thanks
Did you try placing one jumper cap to the socket(to verify if the socket was broken) for the thermistor of extruder0?

Or you can plug the thermistor of heatbed to that socket then see how it shows on LCD,you can get the outcome(the socket or the thermistor itself was broken) as per that.

jeanbraga
Posts: 3
Joined: Tue Mar 21, 2017 9:33 am

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by jeanbraga » Thu Mar 23, 2017 9:27 am

Personally, I bought the Rostock 301 printer, I have a problem in the Extruder and in the extruder that is not heated, the LCD always shows 0 / 0º. I think it may be some printer setup, can anyone help me ??

I tried to contact the company by email and skype but, so far, does not receive any response.

Attached photos.

Please help me.
Ats
Jean Braga

----------- PORTUGUES BRASIL -------------
Pessoal, comprei a impressora Rostock 301, estou com problema nno Extruder e na extrusora que não esta aquece, no visor LCD mostra sempre 0/0º. Penso que pode ser alguma configuração da impressora, alguém pode me ajudar??

Tentei entrar em contato com a empresa por email e pelo skype mas, até o momento não recebe nenhuma resposta.

Fotos em anexo.

Por favor, me ajude.
Ats
Jean Braga
---------------------------------------------------------------------------------------------------------------------------------------------------------
Attachments
img 05.JPG
img 05.JPG (113.55 KiB) Viewed 73156 times
img 04.JPG
img 04.JPG (97.98 KiB) Viewed 73156 times
img 03.JPG
img 03.JPG (82.37 KiB) Viewed 73156 times
img 08.JPG
img 08.JPG (25.97 KiB) Viewed 73156 times
img 07.JPG
img 07.JPG (24.26 KiB) Viewed 73156 times
img 06.JPG
img 06.JPG (34.39 KiB) Viewed 73156 times
imp 02.JPG
imp 02.JPG (48.82 KiB) Viewed 73156 times
imp 01.JPG
imp 01.JPG (97.72 KiB) Viewed 73156 times

ikronos
Posts: 2
Joined: Fri Feb 24, 2017 4:54 am

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by ikronos » Sat Apr 01, 2017 2:56 am

Hello,

A month ago I acquired a printer "Mecreator2 (GT2560 Rev B).", Until a week ago the printer worked correctly.

After finishing an impression, sent from Repetier, a maximum temperature error "ERR MAX TEMP" appeared. Showing the values ​​319º / 320º for the extruder, 67º / 70º for the bed.

Turn the printer off and on if this error disappears, both the extruder and the bed being at room temperature. After resetting the error, proceed as follows: ERR MAX TEMP. "Displaying the values ​​319º / 320º for the extruder, 67º for the bed.

After consulting in the Forum, the topic viewtopic.php?f=23&t=17030 without serving the solutions provided

According to the viewtopic.php?f=23&t=17030 topic,
I have disconnected the bed, and the extruder cable from the back of the printer, so thermistors should not signal, but the error after resetting, is not erased, nor does it change MAX Temp.

I have put the firmware indicated in the forum for the printer "Mecreator2" but also not be solving the problem.

The three motors of the x, y, z axis and the extruder operate correctly, but there is no way to print, as the error is not erased.

With a multimeter I measured the purple-gray and yellow-brown extruder cables with 630 and 612 ohms with an ambient temperature of 20º.

I have also measured the blue and green wires of the bed, without getting any value.


What is happening? How do I solve this problem?

J. E.

changastyle
Posts: 4
Joined: Tue Jun 06, 2017 1:11 am

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by changastyle » Tue Jun 06, 2017 3:23 am

Could anyone fix this issue? Or just keeped yours printers not working?

terrapetros
Posts: 4
Joined: Tue Feb 21, 2017 7:19 am

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by terrapetros » Tue Jun 06, 2017 8:08 pm

Mine is still not working. i will bring it to a FABLAB in my city to see if someone can fix it.
:o :o :o

venum
Posts: 5
Joined: Sat Dec 10, 2016 5:50 am

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by venum » Fri Jun 30, 2017 2:48 am

bonjour a tous

il y a personne qui a trouver une solution a se problème ?

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by William » Tue Nov 13, 2018 1:49 pm

barker wrote:
Sun Nov 11, 2018 8:10 am
Hello I recently acquired my very first 3d printer. After a lot of assembly time and the replacement of a faulty engine I am going to calibrate my printer, and during a test to see if my tray was at the correct distance from my extruder, an error appeared on the "LCD ERR MAX TEMP BED" and I saw the temperature of the plate at 270 C while I could put my hand over it.This error does not allow me to print. Someone would have a solution? Thank you for your answers.
Try to replace the thermistor of hotend and heatbed.
Then you can get the result:The issue is the broken thermistor or not.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

TheHyperion
Posts: 2
Joined: Mon Oct 21, 2019 10:07 am

Re: How to slove the problem of MAX/MIN TEMP error(GT2560)

Post by TheHyperion » Mon Oct 21, 2019 10:09 am

I am having the same issue after installing your latest firmware. I had no temp issues prior to the firmware update and the terminstors test fine.

Post Reply