Stripping power wires for heating elements

Post Reply
Skwint
Posts: 3
Joined: Wed Nov 28, 2018 4:26 am

Stripping power wires for heating elements

Post by Skwint » Wed Nov 28, 2018 4:32 am

Building an I3 Pro W. Pretty much built.

The heating wires for the extruder and the heatbed need connecting to the green or blue connection points on the bottom of the control board. I don't understand the connection. There is no bare wire visible. Do I need to strip the end of the wires before I put them in?

User avatar
_kaktus_
Site Admin
Posts: 1255
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Stripping power wires for heating elements

Post by _kaktus_ » Wed Nov 28, 2018 4:51 am

Hello.
:mrgreen:

Can you show the photo :?:
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

User avatar
William
Site Admin
Posts: 5111
Joined: Tue Jun 07, 2016 9:38 am

Re: Stripping power wires for heating elements

Post by William » Wed Nov 28, 2018 9:39 am

Attach your photos,please. :D
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Skwint
Posts: 3
Joined: Wed Nov 28, 2018 4:26 am

Re: Stripping power wires for heating elements

Post by Skwint » Wed Nov 28, 2018 7:00 pm

Photo of the ends of the wires that need connecting:
https://i.imgur.com/5YW26IM.jpg

User avatar
_kaktus_
Site Admin
Posts: 1255
Joined: Fri Dec 15, 2017 10:06 pm
Location: PL
Contact:

Re: Stripping power wires for heating elements

Post by _kaktus_ » Wed Nov 28, 2018 11:06 pm

HI
:mrgreen:

You thought well.
On your own, you have to remove the insulation from the end of the wires.

It is also good to solder the ends with tin. ;)
On the forum I help to use the rod, I don't give fish.
Geeetech Prusa I3 M201 Dual extruder Mixcolor 3D printer, bought 2017-12-19, already built, in the cognitive and improvement phase
Geeetech filament, ABS only
Geeetech 3D WiFi Module for 3D Printer, bought 2018-04-15, He got a new life, and still lies in a drawer.
Positively frenzied customer of Getech Technology.

User avatar
William
Site Admin
Posts: 5111
Joined: Tue Jun 07, 2016 9:38 am

Re: Stripping power wires for heating elements

Post by William » Thu Nov 29, 2018 1:42 pm

_kaktus_ wrote:
Wed Nov 28, 2018 11:06 pm
HI
:mrgreen:

You thought well.
On your own, you have to remove the insulation from the end of the wires.

It is also good to solder the ends with tin. ;)
Kaktus is correct.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests