Page 3 of 6
Re: For people who wants STL files of parts
Posted: Thu Jul 09, 2015 6:19 pm
by Buzz
Thank you for the attention and fast response, Eric.
Re: For people who wants STL files of parts
Posted: Wed Jul 15, 2015 5:05 am
by leo
I purchased your dual extruder and am installing it on a Prusa i3 printer. The dual extruder holder stl file does not fit the dual extruder I purchased. You have no heatsinks and one fan on the extruder provided with your pro c printer kit but the dual extruder you sell separately has 2 heatsinks and two fans so it won't fit the holder. Is it ok to install without the heatsinks? Why 2 different versions of the same thing? No stl file for a holder that will fit mine?
Thanks
Re: For people who wants STL files of parts
Posted: Wed Jul 15, 2015 6:25 am
by The3DStudent
Are the printed parts (stl files) for the Prusa i3 pro C the same as the i3 B? I realize the dual extruder mount is already listed separately, but I do not see a listing for the other i3 C parts. If they are not the same could you please post them or send them in an email?
On another note, this thread is not the easiest thing to find and does not appear when searching the forums for "stl". Perhaps you could put a link to this thread in the build instructions or on the webpage for each of these printers. A better solution would be to add a "downloads" section to your main page or to each printer's webpage; in this section you could provide stl files as well as firmware files saving everyone a great deal of time.
the3dstudent@gmail.com
Re: For people who wants STL files of parts
Posted: Wed Jul 15, 2015 4:39 pm
by Sherry
leo wrote:I purchased your dual extruder and am installing it on a Prusa i3 printer. The dual extruder holder stl file does not fit the dual extruder I purchased. You have no heatsinks and one fan on the extruder provided with your pro c printer kit but the dual extruder you sell separately has 2 heatsinks and two fans so it won't fit the holder. Is it ok to install without the heatsinks? Why 2 different versions of the same thing? No stl file for a holder that will fit mine?
Thanks
hi,could you take a picture of you new dual extruder and heat sink?
Re: For people who wants STL files of parts
Posted: Wed Jul 15, 2015 5:00 pm
by Sherry
hi,these stl files are the same,could you please take a picture of "mount" and "thread" in the review.i'm not sure whict part you describe.thx.
Re: For people who wants STL files of parts
Posted: Thu Jul 16, 2015 1:24 pm
by The3DStudent
"Thread" == forum topic/question and all associated replies
Which stl files are for the Prusa i3 pro C with dual mk8 extruders(see link below)?
http://www.geeetech.com/unassembledgeee ... p-927.html
Re: For people who wants STL files of parts
Posted: Wed Dec 09, 2015 3:40 am
by plee1024
Are the i3x .STL parts availabe?
Re: For people who wants STL files of parts
Posted: Wed Dec 09, 2015 2:03 pm
by Mark
I3 X have no printed plastic parts so there's no stl files for it.
Re: For people who wants STL files of parts
Posted: Fri Jul 22, 2016 2:04 am
by chase
Hi,
Which if any of the above be for an 8mm Acrylic i3 Pro B and C?
tia
Re: For people who wants STL files of parts
Posted: Fri Jul 22, 2016 10:17 am
by William
chase wrote:Hi,
Which if any of the above be for an 8mm Acrylic i3 Pro B and C?
tia
Hi,
What your "8mm" means?