Slic3r two-color printing with Geeetech i3 pro C

gpau
Posts: 50
Joined: Wed Nov 30, 2016 5:35 pm

Slic3r two-color printing with Geeetech i3 pro C

Post by gpau » Tue Jan 10, 2017 5:34 am

Hi,
How do I configure my Geeetech i3 Pro C with slic3r to print two colors?
Thanks

Cup
Posts: 123
Joined: Fri Jul 15, 2016 6:11 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by Cup » Wed Jan 11, 2017 10:11 am

You can refer to this section in your ProC User Manual:
QQ截图20170111101009.jpg
QQ截图20170111101009.jpg (58.25 KiB) Viewed 14154 times

gpau
Posts: 50
Joined: Wed Nov 30, 2016 5:35 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by gpau » Sun Feb 05, 2017 6:56 am

hi,
I tried as instructed but the two-color printing will not start.
That configuration should use on repieter to make it work?

gpau
Posts: 50
Joined: Wed Nov 30, 2016 5:35 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by gpau » Thu Feb 09, 2017 3:02 pm

Hi,
where I find this file for geeetech i3 pro c?
I3B_2E_config_bundle.ini

bang
Posts: 402
Joined: Wed Dec 28, 2016 2:12 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by bang » Thu Feb 09, 2017 5:47 pm

Check if there is relevant code in G-gode file for the heating of extruder1 and extruder2 after slicing the model.

gpau
Posts: 50
Joined: Wed Nov 30, 2016 5:35 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by gpau » Thu Feb 09, 2017 5:58 pm

Here
; generated by Slic3r 1.2.9 on 2017-02-09 at 10:56:30

; external perimeters extrusion width = 0.30mm
; perimeters extrusion width = 0.30mm
; infill extrusion width = 0.40mm
; solid infill extrusion width = 0.40mm
; top infill extrusion width = 0.40mm

M107
M190 S80; wait for bad temperature to be reached
M104 S200; set extruder temperature
G28 ; home all axes
G1 Z5 F5000 ; lift nozzle

G21 ; set units to millimeters
G90 ; use absolute coordinates
M82 ; use absolute distances for extrusion
G92 E0

gpau
Posts: 50
Joined: Wed Nov 30, 2016 5:35 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by gpau » Thu Feb 09, 2017 11:42 pm

Why the press so?
It moves everything right and does not go downtown
Do not look at the quality I have to fine tune the dish.
Attachments
IMG_4097.JPG
IMG_4097.JPG (183.37 KiB) Viewed 14075 times

bang
Posts: 402
Joined: Wed Dec 28, 2016 2:12 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by bang » Fri Feb 10, 2017 8:56 am

You mean what?The white part?
What does the model look like?

gpau
Posts: 50
Joined: Wed Nov 30, 2016 5:35 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by gpau » Fri Feb 10, 2017 4:31 pm

It is the cone that I downloaded here

http://www.thingiverse.com/thing:21773

bang
Posts: 402
Joined: Wed Dec 28, 2016 2:12 pm

Re: Slic3r two-color printing with Geeetech i3 pro C

Post by bang » Sat Feb 11, 2017 4:55 pm

I guess you didn't configure the two settings in your slicer settings?
QQ截图20170211165130.jpg
QQ截图20170211165130.jpg (57.17 KiB) Viewed 14058 times
QQ截图20170211165040.jpg
QQ截图20170211165040.jpg (57.21 KiB) Viewed 14058 times

Post Reply