Burning firmware through the USB port of GTM32 board

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Burning firmware through the USB port of GTM32 board

Post by Mark » Mon Mar 14, 2016 2:51 pm

Instructions of the Firmware Burning through USB Connection of GTM32 (REV B)

Download the firmware here:
http://www.geeetech.com/forum/viewtopic ... 20&t=17046
Note: this is the latest firmware V1.0.5, updated in 3-30-2016, fixed some bugs. For further information please come to here:
http://www.geeetech.com/forum/viewtopic ... 20&t=17279

Note: If your GTM32 board is using the USB port like this one, then you need to install the firmware as follows. And if your board is REV A that has a micro USB port, then please come to this link:
http://www.geeetech.com/forum/viewtopic ... 20&t=17173
01.jpg
01.jpg (421.32 KiB) Viewed 74070 times
002.jpg
002.jpg (272.72 KiB) Viewed 74070 times
Preparations for firmware burning:
1) Download the software for burning: Flash Loader Demonstrator V2.6.0:
http://www.geeetech.com/wiki/images/3/3 ... trator.zip

2) After downloading, please unzip the software and install it.
3) Unzip to get this file:
001.jpg
001.jpg (28.86 KiB) Viewed 74070 times
Double-click to do installation:
02.jpg
02.jpg (94.11 KiB) Viewed 74070 times
For the setting here, please follow its default:
03.jpg
03.jpg (144.79 KiB) Viewed 74070 times
04.jpg
04.jpg (75.79 KiB) Viewed 74070 times
Here you can choose to install it in different destination folders. Here we select the D drive:
05.jpg
05.jpg (82.5 KiB) Viewed 74070 times
06.jpg
06.jpg (153.43 KiB) Viewed 74070 times
07.jpg
07.jpg (81 KiB) Viewed 74070 times
08.jpg
08.jpg (103.17 KiB) Viewed 74070 times
09.jpg
09.jpg (90.15 KiB) Viewed 74070 times
So far, the installation is completed.

Firmware burning

Note: All of the pins are on high electrical level when you are burning the firmware. So the extruder and the hot bed will be in a state of being heated. Please make sure to turn off the main power or unplug the plug of the hot bed and heating rod in order to protect you from being burned.

1) Before burning the firmware through USB connection, you need to insert 2 corresponding jumper caps on the control board.
12.jpg
12.jpg (205.24 KiB) Viewed 74373 times

2) Connect USB cable. After the successful connection with computer, you need to press the RESET button in the top right corner of the control board to reset.
13.jpg
13.jpg (228.61 KiB) Viewed 74373 times
3) Open the Flash Loader Demonstrator:
14.jpg
14.jpg (110.5 KiB) Viewed 74070 times
Confirm the COM port, for the rest please do the setting as default. Click the Next.
15.jpg
15.jpg (91.7 KiB) Viewed 74070 times
16.jpg
16.jpg (77.08 KiB) Viewed 74070 times
17.jpg
17.jpg (183.75 KiB) Viewed 74070 times
As shown in the following picture, choose the firmware you need to burn, and click Next to install it.
18.jpg
18.jpg (126.88 KiB) Viewed 74070 times
19.jpg
19.jpg (147.9 KiB) Viewed 74070 times
20.jpg
20.jpg (131.75 KiB) Viewed 74070 times
It means the burning is successful if you see the words of “download operation finished successfully!”, as shown in the following picture.
21.jpg
21.jpg (117.11 KiB) Viewed 74070 times

Attention: be sure to remove the jumper caps after installing the firmware.

stado65
Posts: 32
Joined: Fri Dec 18, 2015 4:55 am

Re: Burning firmware through the USB port of GTM32 board

Post by stado65 » Tue Mar 15, 2016 2:41 pm

Hi,
what are the differences between Rev A and Rev B version of the GTM32 ?
I see at least : the USB connector, the CMS mosfets...
Last edited by stado65 on Sat Apr 02, 2016 11:21 pm, edited 1 time in total.

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: Burning firmware through the USB port of GTM32 board

Post by Mark » Tue Mar 15, 2016 3:11 pm

the two points you said are all the differences between this two boards, no other difference.

mwout
Posts: 1
Joined: Fri Apr 08, 2016 5:03 pm

Re: Burning firmware through the USB port of GTM32 board

Post by mwout » Fri Apr 08, 2016 6:25 pm

Hi Mark, the link for the Flash Loader Demonstrator V2.8.0 is not functioning anymore

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: Burning firmware through the USB port of GTM32 board

Post by Mark » Fri Apr 08, 2016 11:08 pm

Thanks mate, I'll upload the tool later as I'm not at work this weekend.

RogerBritt
Posts: 1
Joined: Fri Aug 05, 2016 3:05 am

Re: Burning firmware through the USB port of GTM32 board

Post by RogerBritt » Sun Aug 07, 2016 3:31 am

Hi...thanks for sharing this useful information here. I want to know if any other difference is there in both versions other than discussed? Can you please tell me when these release happened? Also i want to know what more applications it added into its features?

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: Burning firmware through the USB port of GTM32 board

Post by William » Mon Aug 08, 2016 10:53 am

Just the USB connector, the CMS mosfets...That's all..
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

MartinHuigh
Posts: 2
Joined: Thu Oct 13, 2016 4:02 am

Re: Burning firmware through the USB port of GTM32 board

Post by MartinHuigh » Sun Oct 16, 2016 5:12 pm

Hi, i made changes to the M201 printer: i've installed a E3dv6 hotend, so no more mixing filament. How do i customize the firmware for this change. IE : ive have another thermistor + the second steppermotor is still being controled.

I only can see the .hex code, not something i can edit using arduino.

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: Burning firmware through the USB port of GTM32 board

Post by William » Mon Oct 17, 2016 9:25 am

@MartinHuigh
The firmware for M201 is not open source,and you don't need to make the change in the firmware cuz it just lose the mixer function when you change a E3dv6 hotend.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

MartinHuigh
Posts: 2
Joined: Thu Oct 13, 2016 4:02 am

Re: Burning firmware through the USB port of GTM32 board

Post by MartinHuigh » Mon Oct 17, 2016 5:41 pm

OK, it's clear for me now... I'll replace the GTM32 board with something open source. I'll keep the 2to1 extruder + GTM32 board apart as a set for future projects, for now my desire is to print with 1 extruder and a opensource board with Marlin. ( I''ll just recently stepped into 3d printing and bought a used M201)

Post Reply