Videos of MK8 Extruder assembly

Post Reply
zhangxueyou
Posts: 1405
Joined: Fri Feb 06, 2015 1:33 pm

Videos of MK8 Extruder assembly

Post by zhangxueyou » Fri May 29, 2015 10:35 am

In this video, you will see how to tear the mk8 extruder down, and how to replace new extruder kits.
https://www.youtube.com/watch?v=aPvVUZQnOMM
How to replace extruder thermistor:
https://www.youtube.com/watch?v=FR0n2FHrjmc
How to replace nozzle:
https://www.youtube.com/watch?v=t2tUxrZDi8o
How to level dual extruder:
https://www.youtube.com/watch?v=XGpcueI ... e=youtu.be

mava70
Posts: 20
Joined: Sun Nov 01, 2015 8:20 am

Re: Videos of MK8 Extruder assembly

Post by mava70 » Wed Nov 25, 2015 5:29 am

hello the heater and the thermistor move inside the hole out and in, can be fixed someway?

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: Videos of MK8 Extruder assembly

Post by Mark » Wed Nov 25, 2015 2:44 pm

there's a setscrew for the heating cartridge, did you see that? and you can use a cable tie to tie them up.

mava70
Posts: 20
Joined: Sun Nov 01, 2015 8:20 am

Re: Videos of MK8 Extruder assembly

Post by mava70 » Wed Nov 25, 2015 3:15 pm

Hello there is a small hex screw next to the hole in the back but I tryed to turn clockwise the screw go inside the hole a lot but don't fix. Should I turn a lot more?

Mark
Posts: 1553
Joined: Thu Aug 06, 2015 9:19 am

Re: Videos of MK8 Extruder assembly

Post by Mark » Wed Nov 25, 2015 3:56 pm

I remember the setscrew is side of the heating block not in the back, maybe you need to remove the sponge thing to check it, and you can screw it a little tight.
Attachments
QQ截图20151125155347.jpg
QQ截图20151125155347.jpg (67.11 KiB) Viewed 35624 times

calabrovarijo
Posts: 4
Joined: Sun Jun 16, 2019 9:31 pm

Re: Videos of MK8 Extruder assembly

Post by calabrovarijo » Sun Jun 16, 2019 9:44 pm

zhangxueyou wrote:
Fri May 29, 2015 10:35 am
In this video, you will see how to tear the mk8 extruder down, Audacity Find My iPhone Origin and how to replace new extruder kits.
https://www.youtube.com/watch?v=aPvVUZQnOMM
How to replace extruder thermistor:
https://www.youtube.com/watch?v=FR0n2FHrjmc
How to replace nozzle:
https://www.youtube.com/watch?v=t2tUxrZDi8o
How to level dual extruder:
https://www.youtube.com/watch?v=XGpcueI ... e=youtu.be
is side of the heating block not in the back, maybe you need to remove the sponge thing to check it, and you can screw it a little tight.

randyhavens
Posts: 1
Joined: Mon Jul 04, 2022 2:50 pm

Re: Videos of MK8 Extruder assembly

Post by randyhavens » Mon Jul 04, 2022 2:51 pm

You can try removing the sponge thing to check it, and screw it a little tight.
gmail sign up

Post Reply