TEMP TOO LOW

Post Reply
DDDude31
Posts: 3
Joined: Tue Nov 19, 2019 9:57 am

TEMP TOO LOW

Post by DDDude31 » Tue Nov 19, 2019 10:16 am

I have sent an email to the help service which still hasn't replied. I have an a20m printer and whenever I start the print it heats up properly, however, then goes to center, goes back to auto home and displays "TEMP TOO LOW". Therefore, I can't even start the 3d print.
Also, I have PVA as a support material and it never prints for some reason/does not extrude.
I have visited a similar forum complaint but that still did not help
The 3d printer is a very important part of my life. PLZ HELP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! :shock:

PVA link:https://www.amazon.com/Paramount-3D-Nat ... 1574129595
Picture of Printer:
Printer1.JPG
Picture #1
Printer1.JPG (180.9 KiB) Viewed 6096 times
,
Printer2.JPG
Picture #2
Printer2.JPG (235.17 KiB) Viewed 6096 times
As a software I use Cura
PLZ HELP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

User avatar
William
Site Admin
Posts: 6338
Joined: Tue Jun 07, 2016 9:38 am

Re: TEMP TOO LOW

Post by William » Tue Nov 19, 2019 10:40 am

Hi, regarding the print temperature of the nozzle, you need to adjust it.
If your nozzle does not heat up, you need to check that your nozzle wiring is fully connected;
The thermistor at the hot end is then measured.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

DDDude31
Posts: 3
Joined: Tue Nov 19, 2019 9:57 am

Re: TEMP TOO LOW

Post by DDDude31 » Wed Nov 20, 2019 9:04 am

Print4.jpg
Print4.jpg (148.74 KiB) Viewed 6079 times
Print3.jpg
Print3.jpg (148.48 KiB) Viewed 6079 times
Print2.jpg
Print2.jpg (161.27 KiB) Viewed 6079 times
Print1.jpg
Print1.jpg (168.37 KiB) Viewed 6079 times
It heats up fine. Both plate and extruder heat up.
But then when it starts the E1 requirement drops to 0 and then it stops and displays TEMP TOO LOW.

User avatar
William
Site Admin
Posts: 6338
Joined: Tue Jun 07, 2016 9:38 am

Re: TEMP TOO LOW

Post by William » Wed Nov 20, 2019 9:28 am

Hi, you can check if the thermistor wiring of your hot end is fully connected.
The thermistor at the hot end is then measured.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

User avatar
YvonGeee
Posts: 23
Joined: Thu Oct 03, 2019 7:20 pm
Location: Bretagne, France

Re: TEMP TOO LOW

Post by YvonGeee » Wed Nov 20, 2019 6:39 pm

You may want to check your slicer settings...

It happens to me when I make this mistake in Cura:

I want to print with one color only, I select Ext1, then I add some support and by default sometimes it selects the other color for support, if I do not change it to same model color then I have the same issue, it prints the support and then stops heating.

DDDude31
Posts: 3
Joined: Tue Nov 19, 2019 9:57 am

Re: TEMP TOO LOW

Post by DDDude31 » Sun Nov 24, 2019 12:33 am

Hi, this is me. Very sorry about the delay. It seems I have fixed the problem by changing the start and end gcode to what it is supposed to be for Marlin. When I start the print it works just fine but then I came downstairs and noticed that the printer head was "printing" but no filament was coming out. So, it was just floating and nothing printed. Is this just a clog in the extruder?

eliottger
Posts: 3
Joined: Thu Dec 03, 2020 11:10 pm

Re: TEMP TOO LOW

Post by eliottger » Mon Dec 07, 2020 4:18 am

YvonGeee wrote:
Wed Nov 20, 2019 6:39 pm
You may want to check your slicer settings...

It happens to me when I make this mistake in Cura:

I want to print with one color only, I select Ext1, then I add some support and by default sometimes it selects the other color for support, if I do not change it to same model color then I have the same issue, it prints the support and then stops heating.
Hey man! I had the same issue and I changed extruders andnow it works. I think it's because the extruder doesn't have its own hotend. Do you know how to work your way around it? help would be greatly appreciated.

loko_lorenzo
Posts: 2
Joined: Wed Dec 16, 2020 9:30 am

Re: TEMP TOO LOW

Post by loko_lorenzo » Wed Dec 16, 2020 9:41 am

I had this issue but resolved it because I enabled a few different temperature settings in cura. They mustve caused the printer to have conflicting conditions but when I disabled them only leaving the core temp settings like print temp the my A10m started printing normally again. Hope this helps :idea:

Rosetta
Posts: 1
Joined: Mon Jan 04, 2021 5:06 pm

Re: TEMP TOO LOW

Post by Rosetta » Mon Jan 04, 2021 5:08 pm

Thanks for the information. Keep sharing such informatic post. Looking for the same issue.











mymilestonecard
Last edited by Rosetta on Tue Jan 05, 2021 5:03 pm, edited 1 time in total.

ianac2000
Posts: 3
Joined: Sun Jan 03, 2021 4:36 am

Re: TEMP TOO LOW

Post by ianac2000 » Tue Jan 05, 2021 2:01 am

There is a really good youtube video by 1zRadio that explains this issue and how to resolve it

https://www.youtube.com/watch?v=N9x9de4nYI8

essentially it is an issue with the way CURA deals with multi extruders. It tries to be clever and switch the temperature down on the first extruder when using the second. As a result the temp of the (one) nozzle cools and the printer cuts out.

It can be resolved in 2 ways;

1 - set all the temps including the standby temps to the same extrusion temperature
2 - follow the guidance in the youtube video and all a post processing script to remove the code that turns off extruder 1

hope this helps

Post Reply