Search found 1417 matches
- Fri Jul 03, 2015 11:14 am
- Forum: Firmware
- Topic: EndStops problem
- Replies: 27
- Views: 41292
Re: EndStops problem
Hi, do you have any idea, how the fuse is gone?? Remember, the printer was only in stand-by, without any motion and the extruder and the bed where off too. And could you post me the correct reference of this fuse. thank you Some where is short circuit, so the fuse is gone. The reference of the fuse...
- Fri Jul 03, 2015 10:49 am
- Forum: Stepper Motor
- Topic: axis problem
- Replies: 26
- Views: 29540
Re: axis problem
After you raise the temperature properly but you can extruder the filament by your hand, you should check if the nozzle is jammed. Sorry, I was to say" After you raise the temperature properly but you can not extruder the filament by your hand, you should check if the nozzle is jammed." Is the nozz...
- Fri Jul 03, 2015 10:12 am
- Forum: Control Board
- Topic: My Rumba my be fired?
- Replies: 12
- Views: 20021
Re: My Rumba my be fired?
Could you please tell me which M7 is fired.
- Fri Jul 03, 2015 10:11 am
- Forum: Stepper Motor
- Topic: X,Y, & Z axis motors do not move in manual control
- Replies: 3
- Views: 7653
Re: X,Y, & Z axis motors do not move in manual control
When LCD displays "0/0", the corresponding thermistor is not well connected to mainboard, or it is plug to the wrong slot. "Err: min temp" means extruder thermistor is not well connected. "Err: min bed temp" means hot bed thermistor is not well connected. You must let all the axes auto home if you w...
- Fri Jul 03, 2015 8:56 am
- Forum: Others
- Topic: Printing ABS, improve quality
- Replies: 1
- Views: 4666
Re: Printing ABS, improve quality
There is a file that describes something about this, hope it will help you.
- Thu Jul 02, 2015 5:59 pm
- Forum: Software
- Topic: Extruder motor
- Replies: 5
- Views: 9518
Re: Extruder motor
You connect the extruder motor in wrong direction, so the extruder motor can not move. QQ截图20150702175232.png You are the lucky one. Worstly, connecting motor driver will destroy the driver, even the whole mainboard. And the blue part on board must be near to cooling fan, when heating the be, the te...
- Thu Jul 02, 2015 5:46 pm
- Forum: Software
- Topic: Error Max Temp Bed
- Replies: 15
- Views: 30494
Re: Error Max Temp Bed
What are the resistance of hot bed thermistor and extruder thermistor? Are they both around 90k ohm?
- Thu Jul 02, 2015 4:05 pm
- Forum: Stepper Motor
- Topic: Y axis stepper motor issue
- Replies: 22
- Views: 29850
Re: Y axis stepper motor issue
Please check if y endstop is fine:
Swap x endstop with y endstop. Then click auto home.
Swap x endstop with y endstop. Then click auto home.
- Thu Jul 02, 2015 2:15 pm
- Forum: Extruder
- Topic: Upgrading to Bowden Extruder
- Replies: 9
- Views: 16039
Re: Upgrading to Bowden Extruder
Is there a fan near the hot end?
- Thu Jul 02, 2015 2:02 pm
- Forum: Control Board
- Topic: My Rumba my be fired?
- Replies: 12
- Views: 20021
Re: My Rumba my be fired?
M7? Is it diode?somedud3 wrote:That is what I have, but another problem came up while transporting the board. One of the M7 fried, so I will try to repair that and see.