Search found 1417 matches
- Thu Jul 02, 2015 1:54 pm
- Forum: Extruder
- Topic: How to clear nozzle when it's jammed
- Replies: 13
- Views: 87834
Re: How to clear nozzle when it's jammed
The diameter of the "screw" you say must be equaled to filament diameter.
- Thu Jul 02, 2015 1:52 pm
- Forum: Firmware
- Topic: err: mintemp
- Replies: 6
- Views: 11000
Re: err: mintemp
Is the extruder moving with no filament?rrobertm wrote:Fixed err:mintemp, but now I got another problem: the extruder motor is not working. I moved it on x axis motor connector and it works. After that I switced the small motor modules on the mainboard and the one mounted for the extruder motor is not working.
- Thu Jul 02, 2015 1:51 pm
- Forum: Firmware
- Topic: How to upload the firmware to Sanguinololu
- Replies: 43
- Views: 216914
Re: How to upload the firmware to Sanguinololu/GT2560
Currently, I am stuck with trying to get the extruders to run. I have tested the drivers and motors by swapping them with a working axis and they all test good. I have set the temperature of the extruders to a working range, but still no luck. I get the Protection error message when the temp is set...
- Thu Jul 02, 2015 11:44 am
- Forum: LCD Panel
- Topic: LCD high Pitched Sount
- Replies: 42
- Views: 57717
Re: LCD high Pitched Sount
Either, because it will back to 0 V when you rotate too much. So you need a multimeter to test the voltage between screw and GND.
- Thu Jul 02, 2015 11:42 am
- Forum: Firmware
- Topic: EndStops problem
- Replies: 27
- Views: 41350
Re: EndStops problem
Over high currect caused 10A fuse burnt, you need to replace a new fuse.mallensp wrote:Hi,
as you can see in the picture, there is only one led on.
And i checked the microstep setting too: there are 3 jumper
under each A4988.
- Thu Jul 02, 2015 10:54 am
- Forum: Others
- Topic: Lots of problems
- Replies: 6
- Views: 9830
Re: Lots of problems
Hello, u had right the heating wire must be broken inside the hotend because when i metered the cables individually i actually had a mesurement 11696775_10205807146711106_208852609_n.jpg 11714352_10205807147071115_436681642_n.jpg so i guess it needs replacement, about the fans as i told you both go...
- Thu Jul 02, 2015 10:32 am
- Forum: LCD Panel
- Topic: LCD high Pitched Sount
- Replies: 42
- Views: 57717
Re: LCD high Pitched Sount
Is there remaining tin on board?
- Thu Jul 02, 2015 10:15 am
- Forum: Firmware
- Topic: Delta Rostock mini G2 dual firmware for GT2560
- Replies: 40
- Views: 68276
Re: Delta Rostock mini G2 dual firmware for GT2560
My printer is fully functional with a few exceptions. My autoleveling is faulty - My manual controls work perfectly, but when I send the G29 command the hotends try to leave its own frame and then dances around in a circle while increasing height in an upwards spiral... I tried to print a calibrati...
- Wed Jul 01, 2015 5:59 pm
- Forum: LCD Panel
- Topic: LCD high Pitched Sount
- Replies: 42
- Views: 57717
Re: LCD high Pitched Sount
There is a tool that can remove the melted tin:
- Wed Jul 01, 2015 5:50 pm
- Forum: Software
- Topic: Error Max Temp Bed
- Replies: 15
- Views: 30523
Re: Error Max Temp Bed
I get a reading of 87.8 kilo-ohms from the bed thermistor when I turn on the machine without running the program. But now the error on the display reads "Err: MINTEMP" The bed thermistor looks fine, when the temperature is 25 degrees, it's about 100k ohm. Please check if extruder thermistor is well...