Hi,
Yes, it is. Please refer to the video: https://www.youtube.com/watch?v=fmwMq9t-Nxc&t=13s , and the picture below:
Search found 486 matches
- Wed Nov 03, 2021 6:25 pm
- Forum: Geeetech A20M
- Topic: Tmc2208/9 Drivers
- Replies: 2
- Views: 2800
- Wed Nov 03, 2021 6:17 pm
- Forum: Extruder
- Topic: Bed adhesion probléme after nozzel clogging
- Replies: 6
- Views: 8021
Re: Bed adhesion probléme after nozzel clogging
Hi,
I think you need to set the nozzle temperature to about 240 degrees, clean the hotend, then reload the filament.
I think you need to set the nozzle temperature to about 240 degrees, clean the hotend, then reload the filament.
- Wed Nov 03, 2021 5:52 pm
- Forum: Others
- Topic: Voltage can't drop
- Replies: 0
- Views: 1194
Re: Voltage can't drop
Hi,
The voltage on the motherboard usually is 5V. This is our design.
Best regards
The voltage on the motherboard usually is 5V. This is our design.
Best regards
- Thu Oct 28, 2021 7:24 pm
- Forum: Geeetech A30 Series
- Topic: BLTouch on A30T
- Replies: 1
- Views: 2255
Re: BLTouch on A30T
Hi,
Maybe you can try to turn to top screw like the picture attached, clockwise or counter-clockwise.
Maybe you can try to turn to top screw like the picture attached, clockwise or counter-clockwise.
- Mon Oct 11, 2021 5:13 pm
- Forum: Geeetech A30 Series
- Topic: How can we use PID Autotune on the A30T?
- Replies: 4
- Views: 3997
- Mon Oct 11, 2021 4:53 pm
- Forum: Geeetech I3 Pro B
- Topic: Geeetech super plate hotbed
- Replies: 7
- Views: 8060
Re: Geeetech super plate hotbed
Hi! How can I check where to drop right down to 40c for far superior adhesion? Can you share more insights you found out cause I am still having doubts... domyessay for printing geeetech design The super plate is a little thicker, so you maybe can try to lower the hotbed, or adjust the Z endstop mo...
- Wed Aug 18, 2021 5:03 pm
- Forum: Geeetech A10 Series
- Topic: geetech a10t
- Replies: 1
- Views: 2131
Re: geetech a10t
Hello, it may be a wiring error. Please pay attention to the wiring of 3dtouch, and whether the 3pin and 2pin pins are correctly connected in place.
You can refer to the following video to install:
https://www.youtube.com/watch?v=IaHzsd4DgeU
You can refer to the following video to install:
https://www.youtube.com/watch?v=IaHzsd4DgeU
- Wed Aug 18, 2021 4:59 pm
- Forum: Geeetech A20M
- Topic: A20M - Firmware Update Issue
- Replies: 1
- Views: 2821
Re: A20M - Firmware Update Issue
Hello, you did not choose the correct COM, please refer to the link below to install the CH341 driver.
http://www.geeetech.com/forum/viewtopic ... 974#p81974
http://www.geeetech.com/forum/viewtopic ... 974#p81974
- Tue Aug 10, 2021 10:02 am
- Forum: Geeetech MeCreator2
- Topic: Heating issue...pls help me
- Replies: 1
- Views: 5435
Re: Heating issue...pls help me
Hello, maybe it is the heating wire or the thermistor. Do you have a multimeter? You can measure the resistance of the thermistor and heating rod to see if it is around 90K ohms and 15 ohms.
- Tue Aug 10, 2021 9:59 am
- Forum: Geeetech A10 Series
- Topic: Find motherboard GT2560 V3.0?
- Replies: 1
- Views: 2111
Re: Find motherboard GT2560 V3.0?
Hello, you can contact the sales team of geeetech:
sales@geeetech.com
It is an old motherboard, if it is still in stock, they will provide you with it.
sales@geeetech.com
It is an old motherboard, if it is still in stock, they will provide you with it.