Hello, the tightness of your extruder gear may be the cause of this phenomenon, you can calibrate the extruder, you can refer to the link below for calibration.
https://www.youtube.com/watch?v=xzQjtWhg9VE
Search found 6340 matches
- Tue Sep 08, 2020 9:31 am
- Forum: Extruder
- Topic: A30M Extruding different lengths between sides for same feed length
- Replies: 1
- Views: 10283
- Mon Sep 07, 2020 4:42 pm
- Forum: Geeetech A30 Series
- Topic: Install 3D touch instead of capacitive proximity senso
- Replies: 1
- Views: 4819
Re: Install 3D touch instead of capacitive proximity senso
Hello, you can check if there is an adapter board interface on your hot end, just connect 3d to the adapter board.
- Mon Sep 07, 2020 3:33 pm
- Forum: Geeetech A20
- Topic: Températures bed et extrudeur reviennent toujours à des valeurs non souhaitées.
- Replies: 1
- Views: 7946
Re: Températures bed et extrudeur reviennent toujours à des valeurs non souhaitées.
Bonjour, vous pouvez supprimer directement le startgcode, puis régler la température.
- Mon Sep 07, 2020 11:56 am
- Forum: Geeetech A10 Series
- Topic: GeeeTech A10M not printing.
- Replies: 1
- Views: 2641
Re: GeeeTech A10M not printing.
Hello, according to your description, if your nozzle is not extruding, it may be blocked at the hot end. You can refer to the video below to clean it up. There is another possibility. Please observe whether the temperature of the nozzle reaches 210°C. If possible, you can also take a picture to solv...
- Mon Sep 07, 2020 11:31 am
- Forum: Geeetech I3 Pro B
- Topic: Z Axis Trouble after 3D Touch Install
- Replies: 13
- Views: 19824
Re: Z Axis Trouble after 3D Touch Install
Hello, if your 3dtouch is too far away from the hot bed, you can refer to the link below to adjust the z offset distance.
viewtopic.php?f=27&t=18371
viewtopic.php?f=27&t=18371
- Mon Sep 07, 2020 10:34 am
- Forum: Control Board
- Topic: * SOLVED * Huge problem with GT2560 board
- Replies: 75
- Views: 141858
Re: * SOLVED * Huge problem with GT2560 board
Hello, you can re-upload the new firmware to overwrite it.
- Fri Sep 04, 2020 2:46 pm
- Forum: Geeetech A20
- Topic: Problems with upper layers
- Replies: 3
- Views: 9443
Re: Problems with upper layers
Hello, since you have replaced the nozzle, the extruder has been calibrated, the filament has been replaced, and the hot end has been cleaned. This still happens. So I want you to make a few suggestions: 1. Your consumables may be oxidized, resulting in poor extrusion. You can change to another cons...
- Fri Sep 04, 2020 11:19 am
- Forum: Geeetech A30 Series
- Topic: Change temperature sensor pin Gtm32pro vd board?
- Replies: 1
- Views: 4613
Re: Change temperature sensor pin Gtm32pro vd board?
Hello, if there is no problem with your thermistor, it should be a circuit problem. You can check whether the circuit is broken.
You cannot solve it by changing the pins and updating the firmware, because the firmware of a30 cannot be changed.
You cannot solve it by changing the pins and updating the firmware, because the firmware of a30 cannot be changed.
- Fri Sep 04, 2020 9:32 am
- Forum: Geeetech I3 Pro B
- Topic: Extruder board port not working
- Replies: 2
- Views: 4702
Re: Extruder board port not working
Hello, if you find that the problem is not the driver by replacing the driver, it may be a cable problem. You try to change the cable of another axis to see if it is the problem. It may also be a problem with the structure of the extruder. You can refer to this link. :D http://www.geeetech.com/forum...
- Thu Sep 03, 2020 11:09 am
- Forum: Geeetech A10 Series
- Topic: Micro Swiss hotend
- Replies: 6
- Views: 6860
Re: Micro Swiss hotend
Hello, as long as it can be successfully engaged, it can be used normally. And then adjust the nozzle diameter on the slicing software.