Search found 21 matches
- Wed Jul 10, 2019 10:58 am
- Forum: Geeetech I3 Pro C
- Topic: No way to level bed
- Replies: 16
- Views: 30755
Re: No way to level bed
Both upper and lower rods are 7.83mm in diamter, both upper and lower locking rings are tight.
- Wed Jul 10, 2019 10:08 am
- Forum: Geeetech I3 Pro C
- Topic: No way to level bed
- Replies: 16
- Views: 30755
Re: No way to level bed
This is a bulldog clip : bulldog.jpg There are 4, one at each corner of the glass to fasten it to the heated bed. The glass is flat, the 4 corners all are the same distance from the nozzle (2 sheets of paper), but in the center, the nozzle is against the glass bed... that is flat... the gantry is eq...
- Wed Jul 10, 2019 9:33 am
- Forum: Geeetech I3 Pro C
- Topic: No way to level bed
- Replies: 16
- Views: 30755
Re: No way to level bed
I put a straight edge on the glass bed, and the glass bed its self is flat. The glass bed is held to the heat bed by bulldog clips, not enough pressure to bend the glass. I checked both sides of the glass just in case one side was thicker in the center then the other side.
- Wed Jul 10, 2019 5:15 am
- Forum: Geeetech I3 Pro C
- Topic: No way to level bed
- Replies: 16
- Views: 30755
- Tue Jul 09, 2019 9:14 am
- Forum: Geeetech I3 Pro C
- Topic: No way to level bed
- Replies: 16
- Views: 30755
Re: No way to level bed
when i run it up the sides, its fine, when I move it along the front and back of the bed it hits the bed in the center.
- Tue Jul 09, 2019 7:58 am
- Forum: Geeetech I3 Pro C
- Topic: No way to level bed
- Replies: 16
- Views: 30755
No way to level bed
So, this ever-evolving Pro-C debacle is getting more and more interesting. So. Its printing now, Its running on Marlin 1.0.2, as 1.1.8 was giving me grief. That will come once I can ensure the hardware of the printer is working properly.. and this is where my problem with the impossible to level bed...
- Tue Jul 09, 2019 3:07 am
- Forum: Geeetech I3 Pro C
- Topic: Z Axis Steps problem...
- Replies: 2
- Views: 5117
Re: Z Axis Steps problem...
Turns out the steps was the problem. rather then the 2560 it should have been... it was only 50...
- Tue Jul 09, 2019 3:06 am
- Forum: Geeetech I3 Pro C
- Topic: X-Carriage Replacement
- Replies: 4
- Views: 7935
Re: X-Carriage Replacement
Good idea, I will look into it. I have printed off a set, But I will be doing some modifications to them to help make them more stable.
- Thu Jul 04, 2019 9:40 am
- Forum: Geeetech I3 Pro C
- Topic: Z Axis Steps problem...
- Replies: 2
- Views: 5117
Z Axis Steps problem...
I'm going threw a MESS of a build, I updated to Marlin 1.1.8 and I had a steps problem. I compared it to the 1.0.2 firmware that was on it and made some edits so that things matched. They don't.. My print now looks like this: MVIMG_20190703_183602.jpg The board is an A+ board so the 1.1.8 firmware s...
- Mon Jun 24, 2019 10:46 am
- Forum: Geeetech I3 Pro C
- Topic: X-Carriage Replacement
- Replies: 4
- Views: 7935