Search found 123 matches

by Cup
Fri Dec 30, 2016 11:29 am
Forum: Products FAQ
Topic: First Start Up Wiring Problems ??
Replies: 16
Views: 7686

Re: First Start Up Wiring Problems ??

Freeze on Uploading.JPG I've been attempting to upload the firmware a few times ... I get close ... but the Arduino seems to freeze before upload can complete ... It stops at just before completion as shown below ... This is for the "Full Aluminum Frame I3 Prusa Reprap 3D Printer" How's it going? K...
by Cup
Fri Dec 30, 2016 11:10 am
Forum: Products FAQ
Topic: Issues updating firmware on GT2560
Replies: 2
Views: 1803

Re: Issues updating firmware on GT2560

Hi,
First turn on your printer(power the board),then plug in the USB cable.
by Cup
Fri Dec 30, 2016 11:06 am
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 6078

Re: No Response from stepper motors mini g2s pro

Hi,
I'm suspecting you have a bad PSU.
You can refer this to make some tests:
http://www.geeetech.com/forum/viewtopic ... 18&t=18061
by Cup
Fri Dec 30, 2016 10:59 am
Forum: Others
Topic: Rostock 301 Settings
Replies: 7
Views: 7278

Re: Rostock 301 Settings

Hy, I am Simon from Austria and i print normally with a bq Witbox 2, but some weeks ago i bought a Rostock 301 on Aliexpress, because of the Mix Features, but i have some Troubles with it and i don't know the right Settings and i would be glad for help! I apologize in advance for my bad English ;-)...
by Cup
Fri Dec 30, 2016 10:44 am
Forum: LCD Panel
Topic: i3X LCD stays black
Replies: 25
Views: 12928

Re: i3X LCD stays black

Well didnt even bother to solder a new thermistor to hot bed since it wasnt even connected when that maxtemp bed error was shown, with those jumper caps in. I however did test every way and here are the results: Both thermistors correctly -> Err: MINTEMP Jumper cap in both sockets -> Err: MAXTEMP B...
by Cup
Fri Dec 30, 2016 10:30 am
Forum: Assembly
Topic: Build Platform
Replies: 2
Views: 1861

Re: Build Platform

I am in the process of building a prusa I3X and after I have assembled the build platform it does not run smoothly on the rails. I was wondering if applying WD 40 would help or is there something else i could do. Also when cutting the Y belt is it best to ensure it is a tight fit or leave some slac...
by Cup
Fri Dec 30, 2016 10:17 am
Forum: Assembly
Topic: GEEETech i3x auto home issues
Replies: 1
Views: 1505

Re: GEEETech i3x auto home issues

When i hit auto home the X-axis moves all the way back to the switch, and starts to grind the motor because it doesnt stop. same thing happens with the Y-axis. No idea on where to go from here. Did you have all the endstops correctly connected to the slots(X_min,Y_min and Z_min)? Have a double check.
by Cup
Fri Dec 30, 2016 10:11 am
Forum: Firmware
Topic: I3 Pro C problem
Replies: 3
Views: 2476

Re: I3 Pro C problem

Hi,Percy
Seems like your X motor has a wrong direction,refer to this to modify it in the firmware:
http://www.geeetech.com/forum/viewtopic ... 17&t=17037

As for Y and Z axis,i think you'd better check if you have the two endstops correctly connected to the right slots(Y_min and Z_min).
by Cup
Fri Dec 30, 2016 9:59 am
Forum: Extruder
Topic: Extruder not working
Replies: 123
Views: 127431

Re: Extruder not working

Hello i also have a extruder problem. the plastic comes out in the start of the print but when printing it is not enough. ive checked the extruder motor but it cant push the filament hard enough. i have increased the tension on the wheel on the extruder and i wanted to increase the driver power. bu...