with a break board... it is my intention.
LCD 40 pins flat ribbon connects in and 40 output pins to install what ever type of connector.
Search found 77 matches
- Tue Apr 21, 2020 10:34 pm
- Forum: Geeetech A20M
- Topic: Upgrade A20M/ A10M to 32 bit MAin Board.... ANY one?
- Replies: 21
- Views: 39227
- Wed Jan 29, 2020 11:47 am
- Forum: Geeetech A30 Series
- Topic: leveling problems.
- Replies: 4
- Views: 7648
Re: leveling problems.
use a glass or mirrow.
it will be flat.
adjust your z endstop to correct the glass differences.
or else, contact the seller or Geeetech for resolution.
it will be flat.
adjust your z endstop to correct the glass differences.
or else, contact the seller or Geeetech for resolution.
- Sun Jan 26, 2020 4:17 pm
- Forum: Geeetech A30 Series
- Topic: Geeetech A30M profile setting for Simplify3D and Repetier-Host
- Replies: 22
- Views: 23995
Re: Geeetech A30M profile setting for Simplify3D and Repetier-Host
uncheck : printer has mixing extruder
but you may need to play retraction and purge tower size
i did not try. you will need to test
but you may need to play retraction and purge tower size
i did not try. you will need to test
- Sun Jan 19, 2020 11:15 am
- Forum: A20T
- Topic: A20T vs A20M
- Replies: 1
- Views: 4116
Re: A20T vs A20M
I don’t have the T series.
But in the work to upgrade my M to T.
I have the 3-1. Hot end and it is the same principle as M’s.
But.... it has 3 heating cartridge that it is 6x15mm.
It should heat up quick and evenly.
But in the work to upgrade my M to T.
I have the 3-1. Hot end and it is the same principle as M’s.
But.... it has 3 heating cartridge that it is 6x15mm.
It should heat up quick and evenly.
- Sun Jan 19, 2020 10:01 am
- Forum: Geeetech A20M
- Topic: Note to myself : in 2020, stop printing directly from Cura - Use SD Card instead
- Replies: 3
- Views: 5237
Re: Note to myself : in 2020, stop printing directly from Cura - Use SD Card instead
Raspberry Pi 3b
Long print 16h36mins no issue
Long print 16h36mins no issue
- Sun Jan 19, 2020 7:03 am
- Forum: Geeetech A30 Series
- Topic: leveling problems.
- Replies: 4
- Views: 7648
Re: leveling problems.
make sure before homing (stepper motor are off) your X axis are leveled. use a bubble level. make sure your bed is leveled vs your X axis using the same bubble level. home your X home your Z disable motor home z move x carriage to bed move bed to the nozzle like first corner see how much is your gap...
- Sun Jan 05, 2020 7:14 am
- Forum: A20T
- Topic: Patching A20T firmware for 3dTouch
- Replies: 33
- Views: 58453
Re: Patching A20T firmware for 3dTouch
following
- Thu Jan 02, 2020 12:58 pm
- Forum: Geeetech A20M
- Topic: Cannot keep bed level
- Replies: 7
- Views: 7687
Re: Cannot keep bed level
hope by now you got it sorted out, or returned the printer.
I've been busy with my work and only now New Year holiday breaks...
if not sorted out and not returned your printer, the other thing it might be is the lead screw.
you might want to flip it and see if that helps.
I've been busy with my work and only now New Year holiday breaks...
if not sorted out and not returned your printer, the other thing it might be is the lead screw.
you might want to flip it and see if that helps.
- Thu Jan 02, 2020 12:54 pm
- Forum: Geeetech A20M
- Topic: Where can I find A20m motherboard with correct LCD plug ?
- Replies: 16
- Views: 16441
- Sat Dec 07, 2019 7:59 am
- Forum: Geeetech A20M
- Topic: Cannot keep bed level
- Replies: 7
- Views: 7687
Re: Cannot keep bed level
then we should look at someting mechanical..eg the springs and the knob under the bed. mine is tighten quite a bit, so the bed is well loaded with the spring s' tension on them. this seems to be little things, but, I have seen them to come off during the print sue to the harmonic vibrations on the b...