Search found 10 matches

by Marcellus
Thu Aug 08, 2019 1:44 pm
Forum: Geeetech A30 Series
Topic: Cura 4.2.0 and the A30 Settings [Important]
Replies: 8
Views: 4071

Re: Cura 4.2.0 and the A30 Settings [Important]

rj16066 wrote:
Mon Aug 05, 2019 4:31 am
Question.... All I see is a A30M in the list. Will this profile work on a standard A30

New to 3D printing..

Thanks
Rj

Hello

Dont look for Geetech! Look for Shenzhen Getech Technology, there you will find the A30...

Greets
by Marcellus
Wed Jul 10, 2019 3:35 pm
Forum: Geeetech A30 Series
Topic: A30 firmware.
Replies: 26
Views: 23604

Re: A30 firmware.

Hello

Please tell us when a new firmware will be released (Geeetech A30) ?!?

Greets
by Marcellus
Wed Jul 10, 2019 3:32 pm
Forum: Geeetech A30 Series
Topic: Stop after G29 Startcode
Replies: 11
Views: 3033

Re: Stop after G29 Startcode

Please tell us when a new firmware will be released (Geeetech A30)

Greets
by Marcellus
Wed Jul 10, 2019 3:31 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 388
Views: 1579838

Re: Firmware for geeetech 3D printers

Hello

Please tell us when a new firmware will be released (Geeetech A30) ?!?

Greets
by Marcellus
Wed Jul 10, 2019 3:23 pm
Forum: Geeetech A30 Series
Topic: Stop after G29 Startcode
Replies: 11
Views: 3033

Re: Stop after G29 Startcode

Here is an update: The z-offset is still changing irregularly. Even if you do the autoleveling (capacitive geeetech sensor) before each print you are not on the safe side. I dont know where is the mistake. :? I came across this post, here it seems to be the same problem: https://www.geeetech.com/for...
by Marcellus
Thu Jul 04, 2019 6:04 am
Forum: Geeetech A30 Series
Topic: Stop after G29 Startcode
Replies: 11
Views: 3033

Re: Stop after G29 Startcode

the problem was that I had inserted the G29 command in the startcode. When it's out, autolevel works and the printer starts to print. Some things can be so easy ... :roll: No frimware error, it was user error :oops: And now the z-offset is always 0.6, why ever?!? Now printing is funny thanks for sup...
by Marcellus
Wed Jul 03, 2019 11:12 pm
Forum: Geeetech A30 Series
Topic: Stop after G29 Startcode
Replies: 11
Views: 3033

Re: Stop after G29 Startcode

If it helps you...
HW: V3.3
FW: V1.37.58
by Marcellus
Wed Jul 03, 2019 2:18 pm
Forum: Geeetech A30 Series
Topic: Stop after G29 Startcode
Replies: 11
Views: 3033

Re: Stop after G29 Startcode

Hello William Thanks for information. Extruder and shaft still calibrated. When the Z-Offset is right and i print without sdcard (with usb-connection to pc) all is fine. Quality is good. I can not print from sdcard... and the z-offset changes irregularly. I think its a firmeware bug... when can we h...
by Marcellus
Tue Jul 02, 2019 11:47 pm
Forum: Geeetech A30 Series
Topic: Stop after G29 Startcode
Replies: 11
Views: 3033

Re: Stop after G29 Startcode

Hello Same Problem here with capacitive Sensor. But only when i print from sdcard. Very strange, I get the startgcode from the geeetech sdcard testprint with Editor (i just write the G29 in it) ... Then it works??? But now a few days later it does not work??? I dont change slicer or something... Pri...
by Marcellus
Tue Jul 02, 2019 11:45 pm
Forum: Geeetech A30 Series
Topic: Stop after G29 Startcode
Replies: 11
Views: 3033

Re: Stop after G29 Startcode

Hello Same Problem here with capacitive Sensor. But only when i print from sdcard. Very strange, I get the startgcode from the geeetech sdcard testprint with Editor (i just write the G29 in it) ... Then it works??? But now a few days later it does not work??? I dont change slicer or something... Pri...