Search found 21 matches

by Mr.Hotwire
Fri Apr 03, 2020 8:33 am
Forum: Geeetech I3 Pro C
Topic: Marlin 1.1.8 update problems
Replies: 6
Views: 8712

Re: Marlin 1.1.8 update problems

So this is in my configuration.h #define DEFAULT_AXIS_STEPS_PER_UNIT { 79.89, 80.36, 2603, 95 } //Orig { 80, 80, 4000, 500 } 93*2 = DRV8825 1/32 Stepps Because I have threaded rod NOT Lead screw. I have disconnected the screws from the Z-Axis steppers. And I STILL get the same noise. It is as if one...
by Mr.Hotwire
Fri Apr 03, 2020 6:05 am
Forum: Geeetech I3 Pro C
Topic: Marlin 1.1.8 update problems
Replies: 6
Views: 8712

Re: Marlin 1.1.8 update problems

Its not a bearing, in the 2nd video it was a combo of the shafts and the screws being very bent.

the problem NOW is firmware, Im sure of it.
by Mr.Hotwire
Wed Apr 01, 2020 11:04 am
Forum: Geeetech I3 Pro C
Topic: Marlin 1.1.8 update problems
Replies: 6
Views: 8712

Re: Marlin 1.1.8 update problems

William wrote:
Wed Apr 01, 2020 10:01 am
Hi, you need to install your z-axis fixing plate.
This was also part of the problem,

https://www.youtube.com/watch?v=7sdZNw8r8xk
by Mr.Hotwire
Wed Apr 01, 2020 10:58 am
Forum: Geeetech I3 Pro C
Topic: Marlin 1.1.8 update problems
Replies: 6
Views: 8712

Re: Marlin 1.1.8 update problems

The top plates? I removed them as the threaded rod is so warped, that it rocks the X Axis up and down as it travels on the Z. You will notice that I have red caps on top that hold the guide rods, allowing the threaded rod to spin freely. THIS got rid of my wobble. But that is not the problem, the pr...
by Mr.Hotwire
Wed Apr 01, 2020 7:21 am
Forum: Geeetech I3 Pro C
Topic: Marlin 1.1.8 update problems
Replies: 6
Views: 8712

Marlin 1.1.8 update problems

I have been trying to update my Pro C to Marlin for some time. Its having z axis issues when doing a rapid movement.

Here is a Video that can better explain the issue.

https://youtu.be/A59Ac9Lt2zE
by Mr.Hotwire
Tue Jul 16, 2019 8:55 am
Forum: Geeetech I3 Pro C
Topic: Firmware v1.1.8 not usable
Replies: 9
Views: 6773

Re: Firmware v1.1.8 not usable

All I found was a .hex file, but I have installed new steppers, and THAT helped with 1.1.8 on my GT2560 Rev A.
by Mr.Hotwire
Sat Jul 13, 2019 12:34 pm
Forum: Geeetech I3 Pro C
Topic: Firmware v1.1.8 not usable
Replies: 9
Views: 6773

Re: Firmware v1.1.8 not usable

William wrote:
Thu Jul 11, 2019 10:20 am
Hi, you can refer to this: https://www.geeetech.com/download.html?download_id=35
and the proc don't use 1.18
That link is to a Hex file, not a Marlin / Arduino download. perhaps for an other board?
by Mr.Hotwire
Sat Jul 13, 2019 12:30 pm
Forum: Geeetech I3 Pro C
Topic: Firmware v1.1.8 not usable
Replies: 9
Views: 6773

Re: Firmware v1.1.8 not usable

I have 1.1.8 on my Pro C, and.. My i3 Pro C running Marlin 1.1.8. on a GT2560 Rev A. Things are moving MUCH better now. But, I have run into a problem with the Z Axis. When Z Steps_Per_Unit = 1280 The z moves nice and smooth. But only half the distance ie. 10mm of indication = 5mm of movement When Z...
by Mr.Hotwire
Thu Jul 11, 2019 1:24 am
Forum: Geeetech I3 Pro C
Topic: No way to level bed
Replies: 16
Views: 7952

Re: No way to level bed

yes, there is a heated bed under the glass. My machine is a Pro C.
by Mr.Hotwire
Wed Jul 10, 2019 1:16 pm
Forum: Geeetech I3 Pro C
Topic: No way to level bed
Replies: 16
Views: 7952

Re: No way to level bed

I have checked that the glass is flat, using a straight edge. And the glass is flat.