It should work after you change the dimensions.
I just found out that this profile isn't flagged properly as a dual color profile in simplify3d.
I have fixed that in my current version.
I'm at Gallifrey one convention in Los Angeles right now.
I'll post it as soon as I get back home Tuesday.
Search found 19 matches
- Mon Feb 18, 2019 4:07 am
- Forum: Configuration Profiles Sharing
- Topic: A10M Profile for Simlify3D
- Replies: 20
- Views: 62030
- Mon Feb 04, 2019 9:11 pm
- Forum: Configuration Profiles Sharing
- Topic: A10M Profile for Simlify3D
- Replies: 20
- Views: 62030
Re: A10M Profile for Simlify3D
You are all very welcome!
I'm glad to help.
I'm glad to help.
- Sun Feb 03, 2019 5:55 am
- Forum: Configuration Profiles Sharing
- Topic: A10M Profile for Simlify3D
- Replies: 20
- Views: 62030
Re: A10M Profile for Simlify3D
Woops... I made a typo on the retraction and wipe settings. I set the primary extruder too high.
Here is the update without the mistake.
Here is the update without the mistake.
- Sat Feb 02, 2019 11:36 am
- Forum: Configuration Profiles Sharing
- Topic: A10M Profile for Simlify3D
- Replies: 20
- Views: 62030
Re: A10M Profile for Simlify3D
O.k. I finally have the stringing fixed. Recalibrated the extruders to about 400 pulses per mm. Loosened the extruder tension all the way and then tightened back 2.5 turns. The biggest improvement came with changing out the bowden tube fittings on the extruders. The stock fittings were not holding t...
- Thu Jan 31, 2019 7:43 am
- Forum: Geeetech A10 Series
- Topic: A10M upgrade to 2 extruder 2 nozzle setup
- Replies: 40
- Views: 60848
Re: A10M upgrade to 2 extruder 2 nozzle setup
Hello!
The slicer you are using will have a setting for x y an z offsets for your extruders. Might take a couple of prints to dial it in so your nozzles line up, but it is fairly simple.
The slicer you are using will have a setting for x y an z offsets for your extruders. Might take a couple of prints to dial it in so your nozzles line up, but it is fairly simple.
- Tue Jan 29, 2019 7:06 am
- Forum: Configuration Profiles Sharing
- Topic: A10M Profile for Simlify3D
- Replies: 20
- Views: 62030
Re: A10M Profile for Simlify3D
I don't own an A10, but I don't see any reason that it wouldn't work.
I'm still working on fine tuning stringing issues. Hopefully I'll have a solution this week.
I'm still working on fine tuning stringing issues. Hopefully I'll have a solution this week.
- Mon Jan 21, 2019 3:01 am
- Forum: Configuration Profiles Sharing
- Topic: A10M Profile for Simlify3D
- Replies: 20
- Views: 62030
Re: A10M Profile for Simlify3D
Good Morning!
You are very welcome. I hope all goes well for you.
Here is my latest print using the FFF I posted. I just had to turn on a prime pillar because it is a dual color print.
https://www.youtube.com/watch?v=f5dD7ed5GgI
You are very welcome. I hope all goes well for you.
Here is my latest print using the FFF I posted. I just had to turn on a prime pillar because it is a dual color print.
https://www.youtube.com/watch?v=f5dD7ed5GgI
- Sun Jan 20, 2019 9:50 am
- Forum: Configuration Profiles Sharing
- Topic: A10M Profile for Simlify3D
- Replies: 20
- Views: 62030
Re: A10M Profile for Simlify3D
There is an A10 profile, but it isn't set up for 2 extruders. Also, it doesn't appear to be calibrated right. I have attached my latest FFF file with some slight tweaks. Mainly to fan cooling. I did have to update my extruder steps per mm in the printer firmware. After doing a 100mm extruder calibra...
- Sat Jan 19, 2019 7:47 am
- Forum: Configuration Profiles Sharing
- Topic: A10M Profile for Simlify3D
- Replies: 20
- Views: 62030
Re: A10M Profile for Simlify3D
I just got my A10M last week and have found almost no help in creating an FFF for it. I have assembled the following profile that is fairly decent. I'm having some issues with blobs at the end of each layer. Most likely they would go away if I turned off my octoprint timelapse. It is set to move the...