Search found 13 matches
- Thu Mar 21, 2019 6:46 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10M get rid off 3D touch sensor
- Replies: 3
- Views: 5311
Re: Geeetech A10M get rid off 3D touch sensor
Tried now the 1.1.9 marlin The problem G28 always homes about 8mm above the bed M211 S0 - softwarendstopp disabled leveled G92 Z0 - Z to 0 M500 - remember this M211 S1 - softwareendstop enabled G1 Z10 - 10Up G1 Z0 works now but if G28 then nozzle is 8mm above the Bed, Display says Z 0 Must i disconn...
- Thu Mar 21, 2019 5:52 pm
- Forum: Configuration Profiles Sharing
- Topic: A10M Simplify3d Settings
- Replies: 5
- Views: 30457
Re: A10M Simplify3d Settings
sorry for the late reply,
S3D send me a profile, that works
attached
S3D send me a profile, that works
attached
- Thu Mar 21, 2019 5:48 pm
- Forum: Geeetech A10 Series
- Topic: Geeetech A10M get rid off 3D touch sensor
- Replies: 3
- Views: 5311
Geeetech A10M get rid off 3D touch sensor
I want to disable the touch sensor. Installed a marlin 118 without Touch But it'll not work EEProm deleted Leveled with a peace of paper, after G28 the nozzle is 8mm above the bed ?!?!? M211 S0 - softwarendstopp disabled leveled G92 Z0 - Z to 0 M500 - remember this M211 S1 - softwareendstop enabled ...
- Sun Jan 27, 2019 9:08 pm
- Forum: Geeetech A10 Series
- Topic: Can't print a thing
- Replies: 48
- Views: 64258
Re: Can't print a thing
I have also many prob printing with a10m only the first print, two colored dog from sd, was great What slicer do you use? I'm trying to print something with s3d 4.1.1 I can print with extruder 1, printing with extruder2 gives the error 104 wrong extruder, sometimes also error 109. Same error appears...
- Tue Jan 15, 2019 1:21 pm
- Forum: Geeetech A10 Series
- Topic: A10M Extruder Fans very very loud!!!
- Replies: 4
- Views: 8585
Re: A10M Extruder Fans very very loud!!!
Problem isn't to find the FAN Control, problem is that you can not control the fanspeed even not over the display.
There is no faster or slower reaction by the fan.
There is no faster or slower reaction by the fan.
- Sun Jan 13, 2019 7:45 pm
- Forum: Geeetech A10 Series
- Topic: A10M Extruder Fans very very loud!!!
- Replies: 4
- Views: 8585
Re: A10M Extruder Fans very very loud!!!
I found no way to lower the Speed at cura or s3d.
Does not work.
I'll install 2 * 12V Silent Coolteks at one 24V line, cause teh A10m has 24V Fans.
Therefore i must modify Printhead or find on @ Thingiverse
Does not work.
I'll install 2 * 12V Silent Coolteks at one 24V line, cause teh A10m has 24V Fans.
Therefore i must modify Printhead or find on @ Thingiverse
- Sun Jan 13, 2019 6:49 pm
- Forum: Configuration Profiles Sharing
- Topic: A10M Simplify3d Settings
- Replies: 5
- Views: 30457
Re: A10M Simplify3d Settings
Thanks, i'll take a look at it,
but since i'm using S3d also for my Any i would prefere to use S3d for all of my printers
but since i'm using S3d also for my Any i would prefere to use S3d for all of my printers
- Sun Jan 13, 2019 6:29 pm
- Forum: Geeetech A10 Series
- Topic: A10M - Merlin V2 - Leveling BL Touch
- Replies: 3
- Views: 6698
A10M - Merlin V2 - Leveling BL Touch
I'd tried ist hours but the nozzel is always to near to the bed I found this as a discription to level BL Touch ; preheat for working temperatures M502 ; optionally reset to firmware settings M500; save M851 Z0 ; reset any z-offset G28 ; home all G1 X117 Y117 ; move nozzle in center M211 S0 ; disabl...
- Fri Jan 11, 2019 7:58 pm
- Forum: Configuration Profiles Sharing
- Topic: A10M Simplify3d Settings
- Replies: 5
- Views: 30457
A10M Simplify3d Settings
I've many Problems to using Simplify3d to print with only one filement, left or right side.
Are there somewhere some settings for Simplify3d ?
Are there somewhere some settings for Simplify3d ?
- Sat Jan 05, 2019 2:49 pm
- Forum: Geeetech A10 Series
- Topic: Marlin 1.1.9 firmware for A10M (pre-built, fine-tuned, both with & without 3d touch) by aarli
- Replies: 33
- Views: 138415
Re: Marlin 1.1.9 firmware for A10M (pre-built, fine-tuned, both with & without 3d touch)
*.hex with cura (or other proggies)
*.ino with Arduino
undér windows
*.ino with Arduino
undér windows