Search found 471 matches

by vert
Sat Oct 12, 2019 2:54 am
Forum: Geeetech A10 Series
Topic: Displey of A10
Replies: 3
Views: 74

Re: Displey of A10

A) display cable came loose from the board / cable is damaged
B) board fried / bootloader currupted
these are the 2 known causes of the display showing 2 bars.
by vert
Thu Oct 10, 2019 7:11 am
Forum: Geeetech A20M
Topic: Missing 1 extruder for A20m Move menu
Replies: 2
Views: 93

Re: Missing 1 extruder for A20m Move menu

100% WAI - working as intended this is how the mix feature works look for the mix menu to change vtool 100/0 -> 0/100.
a note to all users who do not understand how 2 in 1 mixing works you will not find any of the 2 in 2 out menus you are mistaken.
by vert
Thu Oct 10, 2019 7:07 am
Forum: Geeetech A10 Series
Topic: A10m only showing one extruder
Replies: 9
Views: 616

Re: A10m only showing one extruder

Did you ever get this fixed. I'm having the same issue. On the printer I only see Extruder not the Extruder 1, Extruder 2 shown in the menu tree document. Thats exactly how the 2 in 1 mixing system works there will only be 1 listed extruder you need a 2 in 2 out setup to have both like you suggest....
by vert
Wed Jul 03, 2019 2:22 am
Forum: Geeetech A10 Series
Topic: A10M Retraction Settings
Replies: 18
Views: 5218

Re: A10M Retraction Settings

I believe the small disks are there in order to prevent filament from extruder one to go up the tube for filament 2, and the other way around (at least that is the problem I had). I don't think it is ok to remove them. it is true they are intended as anti back flow but it is also true these disks a...
by vert
Wed Jul 03, 2019 2:14 am
Forum: Geeetech A10 Series
Topic: TMC2208 Vref - Geared vs Ungeared Feeders
Replies: 6
Views: 1082

Re: TMC2208 Vref - Geared vs Ungeared Feeders

nema 17 motors safely operate at up to 90C with no negative effects you will sooner overheat the drivers then the motors. as for filament melting in the feeder additional cooling should help prevent this or upgrade to a geared feeder preventing the heat transfer from the motor to the filament. on th...
by vert
Wed Jul 03, 2019 2:09 am
Forum: Geeetech A10 Series
Topic: 2ng Extruder not working
Replies: 2
Views: 324

Re: 2ng Extruder not working

mixing extruder is controlled via M163 m164 m165 m166 or by mix menu on lcd you cant directly control motors with mixing extruder. the a10m is not setup as a cyclops configuration that would allow direct control on E0 & E1. assuming you are operating the mixing extruder properly it should then work....
by vert
Thu Jun 27, 2019 1:45 am
Forum: Geeetech A20M
Topic: New A20M with 3D Touch - Nozzle hits bed
Replies: 8
Views: 3112

Re: New A20M with 3D Touch - Nozzle hits bed

console access of your choice & i repeat my self 1000s of times and no one seems to ever listen. I'm sorry, I'm very new to this. What do you mean by console access? I do believe that "people not listening" has more to do with this forum's UI than people not actually listening. I have looked around...
by vert
Wed Jun 26, 2019 9:21 am
Forum: Geeetech A20M
Topic: New A20M with 3D Touch - Nozzle hits bed
Replies: 8
Views: 3112

Re: New A20M with 3D Touch - Nozzle hits bed

removing the z endstop is required due to the probe and endstop being on the same pin failure to do so will result in accuracy loss and false triggering as well as the endstop being a physical blocker preventing any proper probing from happening. disabling #define MIN_SOFTWARE_ENDSTOP_Z is a horrib...
by vert
Fri Jun 21, 2019 12:56 am
Forum: Geeetech A20M
Topic: New A20M with 3D Touch - Nozzle hits bed
Replies: 8
Views: 3112

Re: New A20M with 3D Touch - Nozzle hits bed

Just assembled the A20M, added the 3dTouch, uploaded the firmware to support the 3DTouch and homing or autoleveling puts the nozzle into the bed and the Z motor starts clicking. Ordered this from 3DPrintBay. Printer has while accents instead of blue and there is no glass bed, did I get an old model...
by vert
Wed Jun 19, 2019 7:09 pm
Forum: Geeetech A10 Series
Topic: Marlin bugfix 2.0 pins_GT2560_v3.h
Replies: 4
Views: 812

Re: Marlin bugfix 2.0 pins_GT2560_v3.h

posting this here is counter productive you should submit a pull request to the marlin GitHub to make this correction other wise all of this info will go no where.