Ah, nevermind, I just saw that the original board only comes with 4 4988 stepper drivers, so the one for the second extruder is missing. Have to order an additional one.
I tested it by switching the stepper driver from E1 to E2 and it works.
Search found 20 matches
- Fri Jul 23, 2021 2:55 am
- Forum: Geeetech I3 Pro W
- Topic: Dual Extrusion - Extruder 2 not working
- Replies: 1
- Views: 2690
- Fri Jul 23, 2021 1:45 am
- Forum: Geeetech I3 Pro W
- Topic: Dual Extrusion - Extruder 2 not working
- Replies: 1
- Views: 2690
Dual Extrusion - Extruder 2 not working
Hello, I am trying to use dual extruders. I already configered the Configuration.h file and uploaded the firmware. dual extrusion.PNG So far heating and temperature reading of hotend 1 and hotend 2 are working fine. Extruder 1 is working fine. However, extruder 2 is not working at all. I changed the...
- Tue Oct 27, 2020 2:15 am
- Forum: Geeetech I3 Pro W
- Topic: Changing heatbed dimensions
- Replies: 1
- Views: 8785
Changing heatbed dimensions
Hey everyone, I modified my printer and upgraded to a bigger heatbed. However, the maximum dimensions of the heatbed seem to be set in the firmware of the printer: It is not possible to move out of the original dimensions of the heatbed. The printer just stops. Regards manual control and generated g...
- Sat Jul 27, 2019 6:38 pm
- Forum: Software
- Topic: Easyprint 1.2.6 new bug discovered
- Replies: 14
- Views: 23659
Re: Easyprint 1.2.6 new bug discovered
Hi, but in fact, the support is to protect your dangling parts, so you don't need to adjust the values very much. So are you saying: "Yes, there is a bug in the software, I was wrong to doubt you. The software is not working as intended, but I don´t care, because I tell you, that you do not need th...
- Thu Jul 25, 2019 3:34 pm
- Forum: Software
- Topic: Easyprint 1.2.6 new bug discovered
- Replies: 14
- Views: 23659
- Thu Jul 25, 2019 3:38 am
- Forum: Software
- Topic: Easyprint 1.2.6 new bug discovered
- Replies: 14
- Views: 23659
Re: Easyprint 1.2.6 new bug discovered
I just read a good tutorial on how to improve the print quality when using support. There they experimented with different Z distances. I would very much appreciate it, if this feature was added in a future version of easyprint.
- Wed Jul 24, 2019 4:37 am
- Forum: Software
- Topic: Easyprint 1.2.6 new bug discovered
- Replies: 14
- Views: 23659
Re: Easyprint 1.2.6 new bug discovered
OH, you can observe the distance transform I set However, we set up support to ensure that the suspended parts do not fall. So can't be set too big. Yes, I can confirm that there is a difference between values <1 mm and >1 mm but there is no difference between values <1 mm. So let´s say 0,1 mm isn´...
- Wed Jul 24, 2019 4:35 am
- Forum: Software
- Topic: Easyprint 1.2.6 new bug discovered
- Replies: 14
- Views: 23659
Re: Easyprint 1.2.6 new bug discovered
Yes, you can set the value but it does not have any effect on the model. I also enabled support interface. I don´t know if this has any influence on it. I took a few screenshots. Here I set the Z-distance to 1 mm. The gap is clearly visible: Z distance 1 mm.JPG Here I set the Z-distance to 0,9 mm. T...
- Tue Jul 23, 2019 2:05 am
- Forum: Software
- Topic: Easyprint 1.2.6 new bug discovered
- Replies: 14
- Views: 23659
Easyprint 1.2.6 new bug discovered
Hallo there, I am currently experimenting with different support settings. There I noticed a bug (I think): Eaysyprint 1.2.6 --> Slicing Settings --> Parameters (---> enable support) --> Z distance: This parameter seems to define the distance between the actual print and the support. The default set...
- Mon Aug 06, 2018 8:40 pm
- Forum: Bug report
- Topic: So many friggin bugs!
- Replies: 5
- Views: 26946