Search found 8 matches

by Ry4n
Tue Apr 28, 2020 3:14 pm
Forum: Geeetech I3 Pro B
Topic: 3DTouch Z-Offset Adjustment
Replies: 6
Views: 2193

Re: 3DTouch Z-Offset Adjustment

I know this is an old post, however for anyone searching around (Like me) the answer I believe is to turn off the software limits. Issue the command M211 S0 to the printer using the terminal in octoprint or pronterface or whatever you use and then you can lower the z axis. once you have the correct ...
by Ry4n
Thu Apr 26, 2018 7:56 pm
Forum: Geeetech I3 Pro W
Topic: 3D_Touch - PRO W - Not working.
Replies: 6
Views: 3218

Re: 3D_Touch - PRO W - Not working.

OK, so here is my firmware. USE THIS AT YOUR OWN RISK, I AM NOT AN EXPERT AND WILL NOT BE HELD RESPONSIBLE FOR ISSUES OR DAMAGES, Check the code ovr prior to installation to make sure its compatible You have been warned. Here is the GCODE start I use in CURA. G21 ;metric values G90 ;absolute positio...
by Ry4n
Wed Apr 25, 2018 7:42 pm
Forum: Geeetech I3 Pro W
Topic: Problem no way
Replies: 9
Views: 3360

Re: Problem no way

Have you re-attached the square power plug from the PSU to the board?
If you don't then the board will only power from USB and wont run the stepper motors.
by Ry4n
Wed Apr 25, 2018 7:38 pm
Forum: Geeetech I3 Pro W
Topic: 3D_Touch - PRO W - Not working.
Replies: 6
Views: 3218

Re: 3D_Touch - PRO W - Not working.

I will post my firmware tonight (UK Time) when I get back from work and you can start from there. From memory one of the key things I had to do was swap the pin in pins.h either from 11 or to 11, I can't recall right now. At that point and once the printer went through the motions of levelling I set...
by Ry4n
Mon Apr 23, 2018 3:19 am
Forum: Geeetech I3 Pro W
Topic: 3D_Touch - PRO W - Not working.
Replies: 6
Views: 3218

Re: 3D_Touch - PRO W - Not working.

Hello, After much pain I think I now have a working printer again. I think there are still tweaks to be made for it to be working fully but it seems to be printing and also using the touch probe. I modified the firmware from this link http://www.geeetech.com/forum/viewtopic.php?f=82&t=61011 so the c...
by Ry4n
Sat Apr 21, 2018 7:08 pm
Forum: Geeetech I3 Pro W
Topic: LCD don't show the menu
Replies: 1
Views: 1348

Re: LCD don't show the menu

Hi,

Do you have the SD and LCD connections the wrong way round?
by Ry4n
Fri Apr 20, 2018 2:56 pm
Forum: Geeetech I3 Pro W
Topic: 3D_Touch - PRO W - Not working.
Replies: 6
Views: 3218

Re: 3D_Touch - PRO W - Not working.

Thanks for the reply.
I started again using stock firmware and the touch sensor is working.

The thing I’m struggling with now is reducing the gap between the extruded and the bed.

The printer won’t go below 000.0 so it won’t go close enough despite changing the offset.

Any advice?

Thanks
by Ry4n
Thu Apr 19, 2018 3:49 am
Forum: Geeetech I3 Pro W
Topic: 3D_Touch - PRO W - Not working.
Replies: 6
Views: 3218

3D_Touch - PRO W - Not working.

Hello All, I seem to be really struggling getting the 3D touch sensor to work. (the sensor looks like this one https://www.geeetech.com/wiki/index.php/3DTouch_Auto_Leveling_Sensor) For some reason the Z axis is pushing my extruder in to the glass bed whatever settings I use its like the Z axis motor...