Search found 1397 matches

by _kaktus_
Thu Oct 17, 2019 1:47 am
Forum: Geeetech A30 Series
Topic: Z-Axis shift between left and right!!!
Replies: 2
Views: 217

Re: Z-Axis shift between left and right!!!

Hello tomriddlepotter.
:mrgreen:

Your idea is not a bad one, but it will also eliminate another phenomenon you don't know about yet. :D
by _kaktus_
Thu Oct 17, 2019 1:45 am
Forum: Geeetech A30 Series
Topic: Replacing the board
Replies: 3
Views: 332

Re: Replacing the board

Hello. :mrgreen: If this controller board has sufficient number of control inputs and outputs you can start this experiment. First of all, look for a firmware with the right functionality you want. Then you have to read a lot about how to connect the sensors. You need to know the order of the leads ...
by _kaktus_
Thu Oct 17, 2019 1:23 am
Forum: Geeetech A30 Series
Topic: Printing multiple colours
Replies: 5
Views: 290

Re: Printing multiple colours

Hi.
:mrgreen:

Greetings and good luck with your experiments.
:D
by _kaktus_
Thu Oct 17, 2019 1:21 am
Forum: Others
Topic: Prusa I3 Pro B - Problem with Y axis
Replies: 6
Views: 2142

Re: Prusa I3 Pro B - Problem with Y axis

Hi
:mrgreen:

And William did it for me.

I would add one more important point. Read more of this forum.
Maybe not all the information will be useful at this stage, but nevertheless. ;)
Have you already found a subforum for your printer model :?:

Greetings to you, sir.
by _kaktus_
Tue Oct 15, 2019 7:36 pm
Forum: Others
Topic: Prusa I3 Pro B - Problem with Y axis
Replies: 6
Views: 2142

Re: Prusa I3 Pro B - Problem with Y axis

Hello.
:mrgreen:

this is called layers shifting, it can be solved successfully.
;)
by _kaktus_
Mon Oct 14, 2019 7:18 pm
Forum: Geeetech A20M
Topic: I have a problem with the extruder.
Replies: 3
Views: 235

Re: I have a problem

Hello. :mrgreen: This happens when the filament does not find an outlet, or is fed too quickly. So it's worth it: Level the heated bed, Adjust the gap between the nozzle and the heated bed surface, Adjust the temperature of the hot end, Check that the Teflon Bowden tubes are properly cut and suffici...
by _kaktus_
Mon Oct 14, 2019 7:07 pm
Forum: Geeetech A20M
Topic: Where can I buy a new extruder for my printer
Replies: 4
Views: 188

Re: Where can I buy a new extruder for my printer

Hello.
:mrgreen:


You can always make a purchase in the company shop.
https://www.geeetech.com/2-in-1-out-dua ... -1038.html
;)
by _kaktus_
Mon Oct 14, 2019 2:41 pm
Forum: Geeetech I3 Pro B
Topic: Chang I3 Dual into M201 Version
Replies: 2
Views: 94

Re: Chang I3 Dual into M201 Version

Hello huyenvu111
:mrgreen:

In my opinion, your goal can be achieved with an existing version of the controller.
Of course, some accessories will need to be replaced.
I suggest that you start your project by finding the firmware in the required version for your controller board. :D
by _kaktus_
Mon Oct 14, 2019 1:20 am
Forum: Software
Topic: easy print 3D scratch slicer
Replies: 2
Views: 76

Re: easy print 3D scratch slicer

Hello.
:mrgreen:

EasyPrint has not been developed by GT for some time now.
Therefore, there may be some conflicts. :roll:

It's a pity, but we can't influence it :?
by _kaktus_
Sun Oct 13, 2019 3:12 pm
Forum: Geeetech I3 Pro W
Topic: All stepper motors not working
Replies: 4
Views: 188

Re: All stepper motors not working

Hello ... I noticed a second issue about Z-axis: the right Z-axis motor often stops while the other on the left is still working, I think this is due to mechanical issues from the threaded rod. But I don't know how to fix it. Maybe searching again in the forum FAQ I'll get an idea. ... Yes, you have...