Search found 10 matches
- Wed Sep 20, 2017 5:35 pm
- Forum: Feedback&Suggestion
- Topic: support
- Replies: 4
- Views: 12857
Re: support
Thanks, now im stuck with the sensor!
- Tue Sep 19, 2017 7:55 pm
- Forum: Feedback&Suggestion
- Topic: support
- Replies: 4
- Views: 12857
support
IN the topic you say "Your suggestions or opinions about our service will be much appreciated" You can for one answer people when they send you an email for support. I have been looking to see how mount and install an auto touch to my I3 pro C , emailing support and other people in your company but ...
- Wed Sep 06, 2017 7:25 pm
- Forum: Mods And Hacks
- Topic: I3 pro C auto level installation
- Replies: 1
- Views: 5339
I3 pro C auto level installation
Hi
Does anyone have the instruction to mount the auto level to I3 pro C dual extruder
all i find is I3 pro B , and any other info that can help/
thansk
Does anyone have the instruction to mount the auto level to I3 pro C dual extruder
all i find is I3 pro B , and any other info that can help/
thansk
- Sat Aug 12, 2017 6:00 pm
- Forum: Project Talent Show
- Topic: My I3 Pro C
- Replies: 6
- Views: 127352
Re: My I3 Pro C
I also had lots of problems with my i3 pro C, But the good thing was that the geeetech people were very helpful to sort them out. As it was mentioned above you need to spend a lots of time to understand your printer and how to use it, Ive spent hours to read about 3d printing and what to do and don'...
- Mon Jul 24, 2017 4:44 pm
- Forum: Print Quality
- Topic: Quality issues of your printed patrts
- Replies: 17
- Views: 88718
Re: Quality issues of your printed patrts
its a new printer so i didnt think it needs cleaning ,how do i clean it ,or check the temprature
- Sun Jul 23, 2017 6:07 pm
- Forum: Others
- Topic: print 2 colour
- Replies: 1
- Views: 4647
print 2 colour
How do you print from the second extruder?
my first one does not work properly want to check if its the extruder or not?
i get this quality.one is a cube and one is a PEZ ,
my first one does not work properly want to check if its the extruder or not?
i get this quality.one is a cube and one is a PEZ ,
- Sat Jul 22, 2017 11:15 am
- Forum: Print Quality
- Topic: Quality issues of your printed patrts
- Replies: 17
- Views: 88718
Re: Quality issues of your printed patrts
HI I have a I3 pro C that i havent been able to get any prints from it till now this is mostly what im getting (see images)seems that it does not feed enough material. the bed is set to 60 and the extruder to 200 degrees. the extruder came without one ofthe white tubes that you feed the filemant in ...
- Sun Jul 16, 2017 3:13 pm
- Forum: Assembly
- Topic: Z axis won’t move on Geeetech Prusa I3 X
- Replies: 15
- Views: 92241
Re: Z axis won’t move on Geeetech Prusa I3 X
I had the same problem along with lots of other problems! i acualy noticed that the 2 shaft that holds the extruder and X motor were quit tight where it goes to the X motor side, i used the files and losened them a little bit ( becarful not to file too much just take the paint away softly) and used ...
Re: I3 Pro C
After going through the whole manual found all the wires but it would have been good to have a sketch of what goes where that the users dont have to waste so much time.
I3 Pro C
Hi I am assembling my I3 Pro ,in the wiring section it says connect X motor to here Y motor to there but no where it says which one X motor or Y motor, The instruction that comes with it shows a video for assembling a similar printer but not exact like there is no mention of the fan that goes behind...