The gt2560 REV a+ include 3pins connector on board
attached manual VERSION 2 PDF
no pin 32 for manuel, it's pin 11 forthe new board
Search found 8 matches
- Mon Jun 12, 2017 2:10 am
- Forum: Geeetech A20M
- Topic: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
- Replies: 326
- Views: 617070
- Tue Jun 06, 2017 11:04 pm
- Forum: Geeetech A20M
- Topic: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
- Replies: 326
- Views: 617070
Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
Hello Here is a video of my problem, in auto home the axis goes up and the pine of the sensor leaves in the vacuum: https://www.youtube.com/watch?v=ej18xi0W_R8 Here is a second video or I reverse the direction of the z axis, So, the z axis goes down well, but another problem, it goes down a can, Ta...
- Tue Jun 06, 2017 1:56 am
- Forum: Mods And Hacks
- Topic: BL/ 3D touch officiel not working correctly
- Replies: 8
- Views: 19532
Re: BL/ 3D touch officiel not working correctly
I found the problem, I disassemble the sensor, and the white wire was unbolted ...
I solder it, and the sensor works;)
I solder it, and the sensor works;)
- Mon Jun 05, 2017 3:47 pm
- Forum: Mods And Hacks
- Topic: BL/ 3D touch officiel not working correctly
- Replies: 8
- Views: 19532
Re: BL/ 3D touch officiel not working correctly
I reset my config by default with the Z axis that goes up, Then we see on the video that I just disconnect the connector (black and white) of the 3d touch and it does the same it goes up https://www.youtube.com/watch?v=p1pDDbgtB1I I also did a test off video, if I invert the (black and white) my tra...
- Mon Jun 05, 2017 3:27 pm
- Forum: Geeetech A20M
- Topic: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
- Replies: 326
- Views: 617070
Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
Hello Here is a video of my problem, in auto home the axis goes up and the pine of the sensor leaves in the vacuum: https://www.youtube.com/watch?v=ej18xi0W_R8 Here is a second video or I reverse the direction of the z axis, So, the z axis goes down well, but another problem, it goes down a can, Tak...
- Mon Jun 05, 2017 3:27 pm
- Forum: Mods And Hacks
- Topic: BL/ 3D touch officiel not working correctly
- Replies: 8
- Views: 19532
Re: BL/ 3D touch officiel not working correctly
Hello Here is a video of my problem, in auto home the axis goes up and the pine of the sensor leaves in the vacuum: https://www.youtube.com/watch?v=ej18xi0W_R8 Here is a second video or I reverse the direction of the z axis, So, the z axis goes down well, but another problem, it goes down a can, Tak...
- Mon Jun 05, 2017 12:59 am
- Forum: Geeetech A20M
- Topic: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
- Replies: 326
- Views: 617070
Re: 3D Touch Sensor:Auto-levelling for Geeetech 3D printer
i have an Pro X ( GT2560 RevA+ Board )with Firmware from the 1st page( + changes for the GT2650 Rev A+) + Setup like described on the wiki + mount for the sensor from the wiki. M280 Po S10 + S90 + S160 are working. if i do G28 -> y,x work, then it goes to the middel and z is going up 3mm, G29 -> th...
- Sun Jun 04, 2017 8:18 pm
- Forum: Mods And Hacks
- Topic: BL/ 3D touch officiel not working correctly
- Replies: 8
- Views: 19532
BL/ 3D touch officiel not working correctly
My printer Geeetech Prusa I3 Pro B (GT2560 REV A+) Hello, I installed a 3dtouch, having the last card, I did not need to solder the 3 pin pin because it is already down to the left which avoids welding ... I plug the Z min. And properly parameterize marlin. My worries when I make an auto-home or lau...