https://www.thingiverse.com/thing:1221968
https://www.thingiverse.com/thing:2135591
Search found 14 matches
- Tue Jun 27, 2017 5:48 am
- Forum: Extruder
- Topic: e3dv6 plus 3d touch
- Replies: 2
- Views: 6135
- Sun Apr 16, 2017 5:45 am
- Forum: Mods And Hacks
- Topic: Improve z-banding on I3 Pro B
- Replies: 2
- Views: 7439
Re: Improve z-banding on I3 Pro B
Thanks for the links etc.. i have had issues with z banding.. and i think in the early stages anyone thats new to 3d printing will come across it. i have seen lots of videos and posts on thingiverse but i have yet to see a proper before and after video / picture. The ones i have seen reduced it, but...
- Fri Apr 07, 2017 3:08 pm
- Forum: Hot bed
- Topic: mk2a heatbed upgrade to mk3 heat bed ?
- Replies: 4
- Views: 26916
Re: mk2a heatbed upgrade to mk3 heat bed ?
Thanks for your lengthy reply. My main reason for changing it is for looks. It worked just fine. At first I was going to install the mk3 Ali bed, and fix it without springs and make use of the 3d touch to level it. I have up on that option after reading hundreds of posts of people not able to get it...
- Fri Apr 07, 2017 5:01 am
- Forum: Hot bed
- Topic: mk2a heatbed upgrade to mk3 heat bed ?
- Replies: 4
- Views: 26916
Re: mk2a heatbed upgrade to mk3 heat bed ?
i purchased the prusa i3 pro b., with the gt2650. i have upgraded the heatbed to mk2b ( black version ) looks much better and voltage etc is almost the same. i do have a mk3 3mm aliminium bed, but the requirements are are a little higher, think i may need a better power supply.. ?
- Fri Apr 07, 2017 4:57 am
- Forum: Assembly
- Topic: Problems with z axxis of prusa i 3A with 3 in one box
- Replies: 1
- Views: 4805
Re: Problems with z axxis of prusa i 3A with 3 in one box
Hi, firstly make sure the bearings are moving freely on the z axis smooth rods, also make sure the x axis rods are not to tight in the carriers and the extruder belt is not to tight. if you are satisfied they are ok, then i would lower / home the z axis. raise by 10 mm and adjust the couplers. na dl...
- Sat Apr 01, 2017 8:13 pm
- Forum: Mods And Hacks
- Topic: Z wobble - Geeetech I3 Pro B - short question
- Replies: 4
- Views: 23411
Re: Z wobble - Geeetech I3 Pro B - short question
There is a difference between z wobble and z banding. The modifications are a mask to hide these.. but not a 100% fix. I had z banding, my first step was to make sure my threaded rods were straight., there were ok, but were very soft, so replaced them straight away. Also the geeetech push rods are v...
- Wed Mar 22, 2017 2:31 am
- Forum: Hot bed
- Topic: mk2a heatbed upgrade to mk3 heat bed ?
- Replies: 4
- Views: 26916
mk2a heatbed upgrade to mk3 heat bed ?
Wow... first post.. Ok im know im not going to get a reply from geeetech. so to everyone else :D has anyone upgraded there mk2a heatbed to the mk3 heatbed. did you upgrade the power supply ? any tips. My main reason for upgrading is i want a black heatbed. i ordered the mk3, then found a mk2b in bla...
- Tue Mar 21, 2017 5:08 am
- Forum: Mods And Hacks
- Topic: who has a 3D or BL touch working?
- Replies: 3
- Views: 9166
Re: who has a 3D or BL touch working?
Thanks for the direction. i dont think there has not been a page i havent read firmware ive tried, or setting. i have also been on numerous other sites covering the bl touch too. giving this sensor an hour is sufficient, which with proper instruction and code should be quite simple. 9 hours wasted w...
- Tue Mar 21, 2017 4:05 am
- Forum: Mods And Hacks
- Topic: piece of crap 3d touch from geeetech.
- Replies: 1
- Views: 6267
piece of crap 3d touch from geeetech.
Ok.. i have purchased this cheap knockoff and have spent a whole day trying to get it working. now if your reading this and considering buying this - DONT. I would rather eat a roll of filament and have my rear end heated to 200`c and print that way than go through the pain of trying to get this wor...
- Tue Mar 21, 2017 3:48 am
- Forum: Mods And Hacks
- Topic: who has a 3D or BL touch working?
- Replies: 3
- Views: 9166
Re: who has a 3D or BL touch working?
Hi, I am suffering the same as you. I have it properly installed it ( correct height ) i have uploaded numerous firmwares and managed to get it to work. all the tests pass without a problem. it goes throught the process of leveling. but when it goes to print its too high from the bed. I have set the...