Search found 9 matches

by uijoti
Thu Feb 09, 2017 11:56 am
Forum: Feedback&Suggestion
Topic: My experience in G2S pro... total fail..
Replies: 3
Views: 2577

Re: My experience in G2S pro... total fail..

I went through an underpowered power supply, but not near the problems you've had. Good work getting that far! I'm at about the same point and it seems adjusting the bed with the screw and wingnut at the base doesn't work. =/ it might for you though. Also got the zstop for autoleveling use an induct...
by uijoti
Mon Feb 06, 2017 12:12 pm
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 5834

Re: No Response from stepper motors mini g2s pro

Its a custom link on a popular stl file site, please contact the author there. Unsure of post rules concerning links to other sites, will pm you.
by uijoti
Wed Jan 04, 2017 11:14 pm
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 5834

Re: No Response from stepper motors mini g2s pro

I was able to get the firmware uploaded and running, and communication established between repetier host and the printer. The error was only happeneing when I tried to initiate the motors from either the computer or the display on the printer. I ended up just using an instance of repetier firmware a...
by uijoti
Wed Jan 04, 2017 6:07 am
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 5834

Re: No Response from stepper motors mini g2s pro

I was unsure about it being a bad power supply as there was no response from the previous poster. I ended up grabbing one out of an old computer and getting it to run the printer (output amperage matched with the unit that came with the printer). Now it runs fine in standalone mode, the extruder and...
by uijoti
Sat Dec 31, 2016 10:49 am
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 5834

Re: No Response from stepper motors mini g2s pro

So, I began unplugging everything again in an attempt to help isolate the issue. I didn't think much of it earlier, but I don't know what the runs of the PCB look like. Could the image below cause a short in the board or something? It's the leads coming through the board from the power supply. http:...
by uijoti
Fri Dec 30, 2016 12:03 pm
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 5834

Re: No Response from stepper motors mini g2s pro

The link you provided is broken into steps. Here are my results from each step. Step 1: Pass Step 2: Pass Step 3: 3.38V on either side of the fuse Step 4: 4.3V It's being under fed by a decent margin. It sounds like the fuse is bad maybe? EDIT: Just to be safe, the board is a GT2560 and I'm running ...
by uijoti
Fri Dec 30, 2016 10:13 am
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 5834

Re: No Response from stepper motors mini g2s pro

I might as well document progress in this thread. Troubleshooting today included: I checked the voltages according to http://www.geeetech.com/forum/download/file.php?id=1512 and they were all grossly under powered. Between 0.4 to 0.6V. I've adjusted them all to be right at 1.1V. I'm getting a little...
by uijoti
Fri Dec 30, 2016 7:05 am
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 5834

Re: No Response from stepper motors mini g2s pro

Can I get input from an admin or something? Did I put this in the wrong subforum? Is this forum not very active? Or am I just screwed? I sent in a ticket with technical support last night but havent received a response.
by uijoti
Thu Dec 29, 2016 12:21 pm
Forum: Others
Topic: No Response from stepper motors mini g2s pro
Replies: 11
Views: 5834

No Response from stepper motors mini g2s pro

Hello all, I'm new to 3d printing and got my first printer for Christmas. I assembled it based on the instructions found in the wiki and am using the version of Marlin from the wiki as well. In the quick setup guide it starts by having the user level the bed with a... well level... by adjusting the ...