Search found 15 matches

by aleXall
Fri Dec 30, 2016 2:47 am
Forum: Print Quality
Topic: Auto Bed Leveling (ABL) issues on G2S Pro
Replies: 2
Views: 3983

Auto Bed Leveling (ABL) issues on G2S Pro

The following message occurs on Repetier msg board, when G29 command run by gcode G29 Auto Bed Leveling ?Probe position out of range. ?Probe position out of range. Instead when I send manually G28 G29 sequence, it works :shock: I've tried also to move G28 G29 lines up or down at start of gcode, with...
by aleXall
Tue Dec 27, 2016 4:31 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 390
Views: 673389

Re: Firmware for geeetech 3D printers

@JLAR200 Download Arduino 1.0.1 and it'll works
by aleXall
Wed Dec 21, 2016 6:27 am
Forum: Print Quality
Topic: G2S Pro Dual extrusion Z level issues
Replies: 12
Views: 9968

Re: G2S Pro Dual extrusion Z level issues

Yes, I do confirm I've fixed Z level issue when extruders switch. Now when I do it manually/by code with T0/T1 codes, Z levels are right. It's important to set corrrectly the boolean values as follows http://i65.tinypic.com/1zn7pn9.jpg I've restarted from beginning with firmware programming, downloa...
by aleXall
Wed Dec 14, 2016 11:00 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 390
Views: 673389

Re: Firmware for geeetech 3D printers

Thank you Cup! After re-downloaded your suggested file RKMB_GT2560_G2S.zip, made changes in configuration.h as suggested in http://www.geeetech.com/wiki/index.php/Delta_Rostock_mini_G2s with more attention then first time and now extruders switching WORKS CORRECTLY ON THE ASSIGNED Z LEVEL ! In the "...
by aleXall
Wed Dec 14, 2016 8:27 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 390
Views: 673389

Re: Firmware for geeetech 3D printers

My Geeetech is G2s Pro. I've downloaded RKMB_GT2560_G2S file.

I want to retry to redownload it.
by aleXall
Wed Dec 14, 2016 5:23 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 390
Views: 673389

Re: Firmware for geeetech 3D printers

Reuploaded firmware with Arduino 1.0.1 and... nothing!! It's going on not working with the 2nd extruder. More! I've tried to manually switch extruders with T commands and each time I do it, spider climbs up 10mm each time when I move spider with G0 or G1 commands. This makes me going nut. And do we ...
by aleXall
Tue Dec 13, 2016 9:18 pm
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 390
Views: 673389

Re: Firmware for geeetech 3D printers

Not yet! I've used Arduino 1.0.6. Does it depends from Arduino ?!? :shock: If you confirm, I'll try it! [EDIT] I've searched back in this topic, and... I realized that I haven't payed attention enough to see your advice about Arduino 1.0.1 (http://www.geeetech.com/forum/viewtopic.php?f=20&t=17181). ...
by aleXall
Tue Dec 13, 2016 2:34 am
Forum: Firmware
Topic: Firmware for geeetech 3D printers
Replies: 390
Views: 673389

Re: Firmware for geeetech 3D printers

Hi, I'm reporting Z level issue dued to extruder switch during two colors printing in this topic http://www.geeetech.com/forum/viewtopic.php?f=26&t=18469 Topic is referred to Geeetech G2s Pro. My printer is one like this. I doesn't know firmware was pre-charged on MB, so I've downloaded and installe...
by aleXall
Sat Dec 10, 2016 2:08 am
Forum: Print Quality
Topic: G2S Pro Dual extrusion Z level issues
Replies: 12
Views: 9968

Re: G2S Pro Dual extrusion Z level issues

Additional informations ... The problem occurs regardless whether or not I use ABL. I also tried to apply gcode M420 (mesh smoothing) unsuccessfully. In this video http://www.youtube.com/watch?v=yqBLLo4SWQs published last June 11, 2016 the G2s seems to work properly (sob!). Since that date how many ...