Search found 11 matches

by Rege
Thu Jun 01, 2017 4:43 am
Forum: Mods And Hacks
Topic: 3D Touch working ... but not totally
Replies: 4
Views: 6347

Re: 3D Touch working ... but not totally

Hello - Thanks for your answer. I tried to raise the Sensor (by changing the support), but the result is the same. I have now a Z offset around 1.8, but when the print starts, after a while the needle fall, even if the sensor led is still active. You may see it in my first video around 1min16s - htt...
by Rege
Wed May 31, 2017 3:34 pm
Forum: Mods And Hacks
Topic: 3D Touch working ... but not totally
Replies: 4
Views: 6347

3D Touch working ... but not totally

Hello, I've an issue with my 3D touch on my I3 PROB acrylic: installed its following the guide, no problem with hardware nor firmware. Tuning of Z offset done. G28 and G29 works fine , and I can see Z motors working during a layer, proof that the sense of the bed is taken in account in my marlin. Vi...
by Rege
Mon Dec 05, 2016 4:40 am
Forum: Extruder
Topic: extruder not pulling enough filament
Replies: 40
Views: 31892

Re: extruder not pulling enough filament

You were right ... Today , I tried to prin something, and no feeding at all -> after checking the extruder upper part is broken... maybe too much effort. I'm really disappointed ... Tried to contact my seller because without the spring load , there were not enough filament so no good print, and now ...
by Rege
Sat Dec 03, 2016 7:30 pm
Forum: Extruder
Topic: extruder not pulling enough filament
Replies: 40
Views: 31892

Re: extruder not pulling enough filament

Hello Thanks @websmr with this feedback, i designed a part to increase the spring pressure http://www.thingiverse.com/thing:1936289 Using the 4mm version seem the better for me. Seem to work fine for me - but now the extruder is missing steps sometimes, but the print is really better See Picture : p...
by Rege
Tue Nov 29, 2016 4:17 am
Forum: Extruder
Topic: extruder not pulling enough filament
Replies: 40
Views: 31892

Re: extruder not pulling enough filament

Still the same problem Can someone help me? I really think that the spring is not strong enough... when I pull the lever with my hand the filament extrudes well. I've seen in another thread that the aluminium version ok MK8 may be the solution... can someone confim? Please Geeetech support team help...
by Rege
Thu Nov 24, 2016 4:40 am
Forum: Extruder
Topic: extruder not pulling enough filament
Replies: 40
Views: 31892

Re: extruder not pulling enough filament

The motor makes the filament move but i think the spring does not press enough ...
Will try to make a video.
by Rege
Wed Nov 23, 2016 2:46 pm
Forum: Extruder
Topic: extruder not pulling enough filament
Replies: 40
Views: 31892

extruder not pulling enough filament

Hello My i3 pro B is finally assembled, and after many try i can't get the extruder to work correctly. Tried many things: - filament is PLA , 1,75mm tested all Temperature until 230° - tuned te steps per unit value in the firmware from 93 (original) to 144, with no change in the result - checked the...
by Rege
Wed Nov 16, 2016 5:23 am
Forum: Assembly
Topic: Noisy Z axis
Replies: 5
Views: 3283

Re: Noisy Z axis

The X axis makes noise too , coming from the linear bearings

For Z axis the noise is mainly from the screw.

Rege
by Rege
Wed Nov 16, 2016 4:27 am
Forum: Assembly
Topic: Noisy Z axis
Replies: 5
Views: 3283

Re: Noisy Z axis

Hello

please find a video to explain: https://youtu.be/u6lSNP0Uhiw

Rege
by Rege
Tue Nov 15, 2016 9:26 pm
Forum: Assembly
Topic: Noisy Z axis
Replies: 5
Views: 3283

Re: Noisy Z axis

Thanks for answering
I will check the links provided but I think a misunderstanding :
It works it is just noisy and seem to be hard for the motor

I will try to make a video tonight.