Search found 38 matches
- Wed Dec 14, 2016 10:03 am
- Forum: Firmware
- Topic: GT2560 FW Marlin and Fan PWM PIN
- Replies: 11
- Views: 31377
Re: GT2560 FW Marlin and Fan PWM PIN
Maybe the mosfet Q5(which controls the PWM signal) on the board was broken.And the voltage should be 12V when controlling it to 100% in Repetier Host.
- Wed Dec 14, 2016 9:47 am
- Forum: LCD Panel
- Topic: Language change
- Replies: 1
- Views: 5110
Re: Language change
Only English.
- Wed Dec 14, 2016 9:46 am
- Forum: Assembly
- Topic: Problems with X Geetech i3 pro C
- Replies: 3
- Views: 7632
Re: Problems with X Geetech i3 pro C
Probably not...You can check if you have endstops correctly connected(X-1,Y-3,Z-5),have a look at the following picture:gpau wrote: it seems strange that all three endstop are broken.
- Wed Dec 14, 2016 9:36 am
- Forum: Firmware
- Topic: GT2560 FW Marlin and Fan PWM PIN
- Replies: 11
- Views: 31377
Re: GT2560 FW Marlin and Fan PWM PIN
You can send the commend "M106 S(0~255)" then measure if the voltage has changes on PWM_Fan slot.
- Wed Dec 14, 2016 9:13 am
- Forum: Extruder
- Topic: Solutions for GT2560 extruder not working
- Replies: 40
- Views: 130587
Re: Solutions for GT2560 extruder not working
You may want to read this:gpau wrote:i,
I put the new marlin, but now for the X-axis should not be more right, is on the contrary.
In the opposite direction to home
http://www.geeetech.com/forum/viewtopic ... 17&t=17037
- Wed Dec 14, 2016 9:11 am
- Forum: Control Board
- Topic: Clik boutton
- Replies: 6
- Views: 8791
Re: Clik boutton
Maybe it's the knob on the LCD has a problem?Didn't you contact the seller?Alain74270 wrote:I have already replace this firmare to this "marlin pi3 pro-b". is it correct ?
Don't work anyway
- Wed Dec 14, 2016 9:05 am
- Forum: Control Board
- Topic: Control board burnt out hot bed connection, etc.
- Replies: 6
- Views: 10385
Re: Control board burnt out hot bed connection, etc.
Hi there My control board has failed it is a GTx2560 board with my Geeetech Prus I3 x brought on 30 of may 2016 what has happened is the connection to the hotbed on the board has burnt out and has failed. i have attached photos. it suddenly happened during a print where the bed was set to 70c. befo...
- Thu Oct 06, 2016 3:04 pm
- Forum: Firmware
- Topic: Can someone actually do photo instruction or YouTube?
- Replies: 2
- Views: 6244
Re: Can someone actually do photo instruction or YouTube?
The user manual states how to make the software Repetier Host,and as for the video,here are some videos about 301,you can refer to the building video of G2s in some places:
https://www.youtube.com/user/geeetech/videos
https://www.youtube.com/user/geeetech/videos
- Thu Oct 06, 2016 2:58 pm
- Forum: Control Board
- Topic: Prusa I3 A Pro Driver Board Not Working
- Replies: 4
- Views: 8769
Re: Prusa I3 A Pro Driver Board Not Working
And how the heating issue goes after you unplug all the stuffs on the board?
- Thu Oct 06, 2016 2:56 pm
- Forum: Control Board
- Topic: Prusa I3 A Pro Driver Board Not Working
- Replies: 4
- Views: 8769
Re: Prusa I3 A Pro Driver Board Not Working
@MarceloSilva
Hi,
As far as i know,Geeetech is on their vacation(Chinese National Day).
I think you can contact the sales(sales@geeetech.com) to have the replacement for the broken parts if you've verified it,and
i believe you will get response from them soon.
Hi,
As far as i know,Geeetech is on their vacation(Chinese National Day).
I think you can contact the sales(sales@geeetech.com) to have the replacement for the broken parts if you've verified it,and
i believe you will get response from them soon.