Search found 38 matches

by ggg666
Wed Dec 14, 2016 10:03 am
Forum: Firmware
Topic: GT2560 FW Marlin and Fan PWM PIN
Replies: 11
Views: 15327

Re: GT2560 FW Marlin and Fan PWM PIN

Maybe the mosfet Q5(which controls the PWM signal) on the board was broken.And the voltage should be 12V when controlling it to 100% in Repetier Host.
by ggg666
Wed Dec 14, 2016 9:47 am
Forum: LCD Panel
Topic: Language change
Replies: 1
Views: 1500

Re: Language change

Only English.
by ggg666
Wed Dec 14, 2016 9:46 am
Forum: Assembly
Topic: Problems with X Geetech i3 pro C
Replies: 3
Views: 2562

Re: Problems with X Geetech i3 pro C

gpau wrote: it seems strange that all three endstop are broken.
Probably not...You can check if you have endstops correctly connected(X-1,Y-3,Z-5),have a look at the following picture:
endstop wiring.jpg
endstop wiring.jpg (135.73 KiB) Viewed 2542 times
by ggg666
Wed Dec 14, 2016 9:36 am
Forum: Firmware
Topic: GT2560 FW Marlin and Fan PWM PIN
Replies: 11
Views: 15327

Re: GT2560 FW Marlin and Fan PWM PIN

You can send the commend "M106 S(0~255)" then measure if the voltage has changes on PWM_Fan slot.
by ggg666
Wed Dec 14, 2016 9:13 am
Forum: Extruder
Topic: Solutions for GT2560 extruder not working
Replies: 38
Views: 34779

Re: Solutions for GT2560 extruder not working

gpau wrote:i,
I put the new marlin, but now for the X-axis should not be more right, is on the contrary.
In the opposite direction to home
You may want to read this:
http://www.geeetech.com/forum/viewtopic ... 17&t=17037
by ggg666
Wed Dec 14, 2016 9:11 am
Forum: Control Board
Topic: Clik boutton
Replies: 6
Views: 2843

Re: Clik boutton

Alain74270 wrote:I have already replace this firmare to this "marlin pi3 pro-b". is it correct ?
Don't work anyway
Maybe it's the knob on the LCD has a problem?Didn't you contact the seller?
by ggg666
Wed Dec 14, 2016 9:05 am
Forum: Control Board
Topic: Control board burnt out hot bed connection, etc.
Replies: 6
Views: 3621

Re: Control board burnt out hot bed connection, etc.

Hi there My control board has failed it is a GTx2560 board with my Geeetech Prus I3 x brought on 30 of may 2016 what has happened is the connection to the hotbed on the board has burnt out and has failed. i have attached photos. it suddenly happened during a print where the bed was set to 70c. befo...
by ggg666
Thu Oct 06, 2016 3:04 pm
Forum: Firmware
Topic: Can someone actually do photo instruction or YouTube?
Replies: 2
Views: 2058

Re: Can someone actually do photo instruction or YouTube?

The user manual states how to make the software Repetier Host,and as for the video,here are some videos about 301,you can refer to the building video of G2s in some places:
https://www.youtube.com/user/geeetech/videos
by ggg666
Thu Oct 06, 2016 2:58 pm
Forum: Control Board
Topic: Prusa I3 A Pro Driver Board Not Working
Replies: 4
Views: 2782

Re: Prusa I3 A Pro Driver Board Not Working

And how the heating issue goes after you unplug all the stuffs on the board?
by ggg666
Thu Oct 06, 2016 2:56 pm
Forum: Control Board
Topic: Prusa I3 A Pro Driver Board Not Working
Replies: 4
Views: 2782

Re: Prusa I3 A Pro Driver Board Not Working

@MarceloSilva
Hi,
As far as i know,Geeetech is on their vacation(Chinese National Day).
I think you can contact the sales(sales@geeetech.com) to have the replacement for the broken parts if you've verified it,and
i believe you will get response from them soon.