Search found 11 matches
- Sat Sep 24, 2016 12:43 pm
- Forum: Products FAQ
- Topic: Slic3r setting for M201 Prusa I3
- Replies: 1
- Views: 4909
Slic3r setting for M201 Prusa I3
Dear Support, I have lost my setting in Repetier-Host Slic3r for my M201 Prusa I3 and I have tried to figure out what was these settings, and I print some examples but I got a bad printing objects. Would you please send me a file for the best setting parameters for Slic3r that you usually used in yo...
- Thu Jan 28, 2016 7:51 pm
- Forum: Products FAQ
- Topic: Support Filament for Prusa I3 M201
- Replies: 1
- Views: 4468
Support Filament for Prusa I3 M201
Hi Mark ...
i would like to know if want to print complicated object that needs "support filament" (PVA Filament) (objects with holes inside) can it done with the M201 ? moreover does the actual temperature the extruder can attempt (some reviews shows 270 oC) ?
Kindly advise
Regards
i would like to know if want to print complicated object that needs "support filament" (PVA Filament) (objects with holes inside) can it done with the M201 ? moreover does the actual temperature the extruder can attempt (some reviews shows 270 oC) ?
Kindly advise
Regards
- Tue Jan 26, 2016 10:22 pm
- Forum: Products FAQ
- Topic: Prusa I3 M201 USB Connection
- Replies: 3
- Views: 7739
Re: Prusa I3 M201 USB Connection
Hi Mark ... I would like to tell you that the solution I found about this issue after a lot of trial was that the server-side for the Repetier-Host was started automatically whenever I launch the application ... therefore it hold the COM port ... so whenever you click the connect button it gave this...
- Fri Jan 22, 2016 1:56 pm
- Forum: Products FAQ
- Topic: The voltage of the motor driver
- Replies: 3
- Views: 7192
Re: The voltage of the motor driver
Hi Mark ... Ok great ... but I have noticed that when I have changed the Driver voltage for Z-axis to 1.0 V instead of 0.6 V ... I am still noticed that the driver is still hot ... is it normal ?
- Wed Jan 20, 2016 4:05 am
- Forum: Products FAQ
- Topic: Prusa I3 M201 USB Connection
- Replies: 3
- Views: 7739
Prusa I3 M201 USB Connection
Hi everyone .... I have download the Repetier-Hos 1.6 and connect it to the M201 successfully and printing a nice cube for testing ... the result was very good ... Then I quit the software .... after 10 min I have tried to reconnect it gives me an error: "Access to the Port COM3 is denied" ... I hav...
- Tue Jan 19, 2016 7:58 pm
- Forum: Products FAQ
- Topic: The voltage of the motor driver
- Replies: 3
- Views: 7192
The voltage of the motor driver
Hi everyone .... I am testing my new Prusa I3 M201 and everything goes well ... I have checked the Voltage for the motor drivers and note that it is for all drivers (3.2 V). Please see attached pictures. Is this good value or it should be 5.0 V as mentioned in the picture ? If not how to adjust the ...
- Tue Jan 19, 2016 7:22 pm
- Forum: Products FAQ
- Topic: Firmware for Prusa I3 M201
- Replies: 5
- Views: 8733
Re: Firmware for Prusa I3 M201
Hi mark ...
Ok ... great .... I will check it ...
But what is the name of firmware used in Prusa I3 M201 ? and is there a way to edit it, like Marlin firmware ? (I used to do that with my old Prusa I3 that I have).
Ok ... great .... I will check it ...
But what is the name of firmware used in Prusa I3 M201 ? and is there a way to edit it, like Marlin firmware ? (I used to do that with my old Prusa I3 that I have).
- Mon Jan 18, 2016 6:07 am
- Forum: Products FAQ
- Topic: Firmware for Prusa I3 M201
- Replies: 5
- Views: 8733
Firmware for Prusa I3 M201
How to modify manually the firmware for Prusa I3 M201? is it easy like marlin firmware?
- Sat Jan 16, 2016 2:39 am
- Forum: Products FAQ
- Topic: Prusa I3 M201
- Replies: 1
- Views: 4402
Prusa I3 M201
Does anyone know If the firmware is already on the M201's controller board or we have to upload it from the internet ?
- Thu Jan 14, 2016 3:41 am
- Forum: Products FAQ
- Topic: Rumba controller board
- Replies: 1
- Views: 4158
Rumba controller board
Can I use this bard for cnc machine and laser cut machine? if yes is there any tutorial or guide for this?