Search found 10 matches
- Sat Jun 13, 2015 10:10 pm
- Forum: Others
- Topic: Heatbed not functioning normally (MOSFET overheats)
- Replies: 5
- Views: 7725
Re: Heatbed not functioning normally (MOSFET overheats)
If it is the value you get after you unplug the heating wires, this hot bed is abnormal. Please contact the customer service, let them re-send you a good one. How are other parts? Are they fine? Yes other parts are great, i'm printing a lot and all goes fine... Wicht department should i mail? And c...
- Fri Jun 12, 2015 3:12 pm
- Forum: Others
- Topic: Heatbed not functioning normally (MOSFET overheats)
- Replies: 5
- Views: 7725
Re: Heatbed not functioning normally (MOSFET overheats)
Yes i did it exactly that way, i saw your pics in an other topic.
I read out between 0.2 and 0.25Ohm. I can make a picture if you want, but at the moment i have a 12+ hours print job so i can do it later on...
I read out between 0.2 and 0.25Ohm. I can make a picture if you want, but at the moment i have a 12+ hours print job so i can do it later on...
- Thu Jun 11, 2015 4:57 pm
- Forum: Others
- Topic: Heatbed not functioning normally (MOSFET overheats)
- Replies: 5
- Views: 7725
Heatbed not functioning normally (MOSFET overheats)
Hi, I contacted the seller on aliexpress where i bought a Geeetech Prusa i3 Pro B, he said i needed to ask here for quicker help, from an engineer. My question to him: My heatbed is not functioning normal. Didn't use it since the Sanguinololu got way to hot, and with PLA it's not necessary. But now ...
- Thu Jun 11, 2015 4:38 pm
- Forum: Others
- Topic: Acrylic frame STL files
- Replies: 3
- Views: 5458
Re: Acrylic frame STL files
Okee i can understand, but how can i fix my broken part? Why don't you sell those parts in the webshop?
- Wed Jun 10, 2015 5:37 pm
- Forum: Others
- Topic: Acrylic frame STL files
- Replies: 3
- Views: 5458
Acrylic frame STL files
Hi, I broke an acrylic part (left-top holder of the Y-axis), but the webshop don't sell them, can you provide me source (DWG/DXF/AI?) files so i can go to a local lasercutter? I prefer all files (from frame + LCD holder), so i don't have to ask if i break any of them again. You can mail them to: jaa...
- Tue Jun 02, 2015 9:39 pm
- Forum: Control Board
- Topic: Extruder port stopped working
- Replies: 6
- Views: 7686
Re: Extruder port stopped working
It was indeed the motor driver! And the min. temp requirements were indeed the troublemaker in my quick test this morning!
Still weird that it stopped halfway on a printjob, but i use little higher temps now so it won't go beneath 180 degrees
Still weird that it stopped halfway on a printjob, but i use little higher temps now so it won't go beneath 180 degrees
- Mon Jun 01, 2015 3:45 pm
- Forum: Control Board
- Topic: Extruder port stopped working
- Replies: 6
- Views: 7686
Re: Extruder port stopped working
I think i had preheating activated @200C, but to be sure i will check when i get home!
If it is the A4988 there is no plroblem, cause i have lots of spares!
Thanks for support so far, i will report back later today.
If it is the A4988 there is no plroblem, cause i have lots of spares!
Thanks for support so far, i will report back later today.
- Mon Jun 01, 2015 3:36 pm
- Forum: Control Board
- Topic: Extruder port stopped working
- Replies: 6
- Views: 7686
Re: Extruder port stopped working
I did tried to swap the A4988 with al others! But without luck.
The e-motor output doesn't work, not with an other motor driver and not with other stepper motor connected.
The e-motor output doesn't work, not with an other motor driver and not with other stepper motor connected.
- Mon Jun 01, 2015 3:19 pm
- Forum: Control Board
- Topic: Extruder port stopped working
- Replies: 6
- Views: 7686
Extruder port stopped working
Hi, All was working fine, but suddenly (while i was printing) my printer stopped extruding. This morning i wanted to test which part was defective. I tried to switch Y motor with the Extruder motor, and the Extruder worked from then on but Y didn't anymore. It should be the board or the A4899 contro...
- Sat May 23, 2015 8:31 pm
- Forum: Firmware
- Topic: How to upload the firmware
- Replies: 12
- Views: 78256
Re: How to upload the firmware
I'm looking for the Sanguino firmware for the GEEEtech i3B Pro Black acrylic 1.75 mm, regular and marlin please so i can use/test both!
Thanks!
Thanks!