Search found 436 matches

by Admin
Tue Jul 27, 2021 2:58 pm
Forum: Geeetech I3 Pro W
Topic: Z Axis out of synch
Replies: 2
Views: 86

Re: Z Axis out of synch

Hello, you can refer to the solutions in the forum to see if it works:
http://geeetech.com/forum/viewtopic.php?f=82&t=60931
http://www.geeetech.com/forum/viewtopic ... 917(thanks
by Admin
Tue Jul 27, 2021 2:57 pm
Forum: Extruder
Topic: A20T 3 in 1 Hotend
Replies: 1
Views: 54

Re: A20T 3 in 1 Hotend

Hello, the hotend structure of A20T is the Teflon tube directly into the hotend, not separate.
by Admin
Tue Jul 27, 2021 2:55 pm
Forum: Geeetech A10 Series
Topic: A10 T druckt nicht richtig
Replies: 1
Views: 40

Re: A10 T druckt nicht richtig

Hello, is the printing condition of the printer very bad, maybe it is not leveled before printing or the extruder is installed or adjusted to cause insufficient extrusion? Or the hotend is blocked. You can find the reason from the above points. If you have any problems and need official help, please...
by Admin
Tue Jul 27, 2021 2:53 pm
Forum: Wifi Box
Topic: Failure to bind to wifi module!!
Replies: 1
Views: 78

Re: Failure to bind to wifi module!!

Hello, it may be wifi expired or unregistered, you can contact your seller to register wifi for you.
by Admin
Tue Jul 27, 2021 2:51 pm
Forum: Geeetech E180 Mini
Topic: GCODE opening sequence getting mad!!
Replies: 1
Views: 52

Re: GCODE opening sequence getting mad!!

Hello, the firmware of E180 is not marlin firmware and does not support every gcode.
by Admin
Tue Jul 27, 2021 2:50 pm
Forum: Geeetech A30 Series
Topic: $700 A30T died after 2 months
Replies: 1
Views: 50

Re: $700 A30T died after 2 months

Hello, you can contact your seller directly. I don't know where you bought the printer. If it is Amazon, you can directly request replacement parts or other requirements.
by Admin
Tue Jul 27, 2021 2:49 pm
Forum: Geeetech A30 Series
Topic: Geeetech a30 Not extruding filament
Replies: 3
Views: 157

Re: Geeetech a30 Not extruding filament

Hello, maybe the hot bed is not leveled correctly?
You can slow down or change the printing area to see if the consumables stick to the hot bed.
by Admin
Wed Jul 21, 2021 3:54 pm
Forum: Geeetech A10 Series
Topic: heating error on control panel
Replies: 1
Views: 86

Re: heating error on control panel

Hello, a negative number indicates that the thermistor wire is disconnected. Please check whether the thermistor connection is normal.
Basically, it shows that the connection line is in poor contact. Please check the connection between the contact line of the extruder and the adapter board.
by Admin
Wed Jul 21, 2021 3:49 pm
Forum: Geeetech A10 Series
Topic: A10M Y Axis came with dents in the slots
Replies: 1
Views: 79

Re: A10M Y Axis came with dents in the slots

Hello, you can contact your seller to request replacement parts.
by Admin
Wed Jul 21, 2021 3:48 pm
Forum: Geeetech E180 Mini
Topic: PRINTER GONE CRAZY OUT OF THE BOXXX !!!
Replies: 2
Views: 132

Re: PRINTER GONE CRAZY OUT OF THE BOXXX !!!

Hello, please contact geeetech's ticket system for official help.

Regarding the reversal of the Z-axis of the printer, it may be a wiring error. You can exchange the wiring sequence of the motor to see if the Z-axis can be restored to normal.
Regards.