Search found 282 matches

by Admin
Mon Nov 23, 2020 4:26 pm
Forum: Geeetech A10 Series
Topic: A10M rotary encoder switch stopped working
Replies: 1
Views: 55

Re: A10M rotary encoder switch stopped working

Hello, there may be a problem with your screen. You can find a solution in the ticket system on the geeetech official website.
by Admin
Mon Nov 23, 2020 4:24 pm
Forum: Geeetech A30 Series
Topic: Geetech A30 break down looking for some help
Replies: 1
Views: 31

Re: Geetech A30 break down looking for some help

Hello, maybe your driver is damaged, you need to contact geeetech technicians for help.
You can find a solution in the ticket system on the geeetech official website.
by Admin
Mon Nov 23, 2020 4:18 pm
Forum: Geeetech A30 Series
Topic: Problems following blown 4988 stepper driver
Replies: 2
Views: 34

Re: Problems following blown 4988 stepper driver

Hello, the situation you mentioned is very serious, you need to find a solution in the ticket of geeetech.
by Admin
Mon Nov 23, 2020 4:18 pm
Forum: Geeetech A30 Series
Topic: Problems following blown 4988 stepper driver
Replies: 2
Views: 34

Re: Problems following blown 4988 stepper driver

Hello, the situation you mentioned is very serious, you need to find a solution in the ticket of geeetech.
by Admin
Wed Nov 11, 2020 2:54 pm
Forum: Geeetech I3 Pro B
Topic: GT2560 Rev.A+ wiring
Replies: 2
Views: 336

Re: GT2560 Rev.A+ wiring

A+接线板.jpg
A+接线板.jpg (598.18 KiB) Viewed 291 times
by Admin
Wed Nov 11, 2020 2:52 pm
Forum: Geeetech I3 Pro B
Topic: GT2560 Rev.A+ wiring
Replies: 2
Views: 336

Re: GT2560 Rev.A+ wiring

Hello, maybe what you need is this. :D
by Admin
Sat Nov 07, 2020 2:44 pm
Forum: Geeetech A20M
Topic: Printer goes to 15-20% and shuts down
Replies: 1
Views: 250

Re: Printer goes to 15-20% and shuts down

Hello, you can exchange e0 and e1 cables, and then try to print to see if e1 is restored. If you can't resume work, it may be that the e1 motor has a problem and needs to be replaced. If e0 becomes abnormal, there may be a problem with the motherboard or driver. :D
Regards.
by Admin
Sat Nov 07, 2020 2:40 pm
Forum: Geeetech A10 Series
Topic: A10M Screen with Bars
Replies: 2
Views: 387

Re: A10M Screen with Bars

Hello, you can first check whether the cable is tightly tied. Then connect the computer to the printer and see if you can control the printer through the computer to complete some basic operations, such as moving, heating, etc. If it works, the screen needs to be replaced. If not, there is a problem...
by Admin
Thu Oct 15, 2020 11:32 am
Forum: Geeetech A10 Series
Topic: problem with firmware A10
Replies: 1
Views: 1479

Re: problem with firmware A10

Hello, you can re-plug the LCD screen cable, there may be a problem with the cable. If it still cannot be removed, there may be a hardware problem. You can contact geeetech's technical support page for help. :D
by Admin
Thu Oct 15, 2020 11:05 am
Forum: Geeetech A10 Series
Topic: Newbee printing problems
Replies: 1
Views: 1014

Re: Newbee printing problems

Hello, it may be that your extruder is loose. You can observe whether the screws are loose and you can adjust them with a screwdriver. It may also be that your printing speed is too fast. The printing speed can be adjusted. :D