# generated by PrusaSlicer 2.5.0+win64 on 2022-10-28 at 01:51:29 UTC

[print:Geeetech Mizar_M@Printing Set]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 60
brim_separation = 0.15
brim_type = outer_only
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0
ensure_vertical_shell_thickness = 0
external_perimeter_extrusion_width = 0
external_perimeter_speed = 60%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
fill_density = 10%
fill_pattern = adaptivecubic
first_layer_acceleration = 0
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.2
first_layer_speed = 20
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 20
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 80
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 0
mmu_segmented_region_max_width = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{print_time}.gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_generator = arachne
perimeter_speed = 60
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.1
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 6
skirt_height = 1
skirts = 1
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thick_bridges = 1
thin_walls = 1
threads = 4
top_fill_pattern = monotonic
top_infill_extrusion_width = 0
top_solid_infill_speed = 15
top_solid_layers = 3
top_solid_min_thickness = 0
travel_speed = 130
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 100%
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_brim_width = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 325
wipe_tower_width = 30
wipe_tower_x = 159
wipe_tower_y = 190
xy_size_compensation = 0

[print:Geeetech——Mizar_M@Printing Set]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 3
bottom_solid_min_thickness = 0
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 60
brim_separation = 0.15
brim_type = outer_only
brim_width = 1.2
clip_multipart_objects = 1
compatible_printers = "Geeetech——Mizar_M@Separated color Module"
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
draft_shield = disabled
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 0
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 10%
fill_pattern = adaptivecubic
first_layer_acceleration = 800
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 20
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 1000
infill_anchor = 600%
infill_anchor_max = 50
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 80
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 0
mmu_segmented_region_max_width = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{print_time}.gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_generator = arachne
perimeter_speed = 60
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.2
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 6
skirt_height = 1
skirts = 1
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2.5
support_material_speed = 60
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 0
support_material_with_sheath = 1
support_material_xy_spacing = 50%
thick_bridges = 1
thin_walls = 1
threads = 4
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 20
top_solid_layers = 3
top_solid_min_thickness = 0
travel_speed = 180
travel_speed_z = 0
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 0.4
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_brim_width = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 325
wipe_tower_width = 30
wipe_tower_x = 159.008
wipe_tower_y = 190.07
xy_size_compensation = 0

[print:Printing Set@Mizar M]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 4
bottom_solid_min_thickness = 0.5
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 0.95
bridge_speed = 25
brim_separation = 0.1
brim_type = outer_only
brim_width = 0
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 0
draft_shield = disabled
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.45
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 0
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.45
fill_angle = 45
fill_density = 10%
fill_pattern = adaptivecubic
first_layer_acceleration = 800
first_layer_acceleration_over_raft = 0
first_layer_extrusion_width = 0.42
first_layer_height = 0.2
first_layer_speed = 20
first_layer_speed_over_raft = 30
fuzzy_skin = none
fuzzy_skin_point_dist = 0.8
fuzzy_skin_thickness = 0.3
gap_fill_enabled = 1
gap_fill_speed = 40
gcode_comments = 0
gcode_label_objects = 1
gcode_resolution = 0.0125
gcode_substitutions = 
infill_acceleration = 1000
infill_anchor = 2.5
infill_anchor_max = 12
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 80
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 200
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_bead_width = 85%
min_feature_size = 25%
min_skirt_length = 4
mmu_segmented_region_max_width = 0
notes = 
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{print_time}.gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_generator = arachne
perimeter_speed = 50
perimeters = 2
post_process = 
print_settings_id = 
raft_contact_distance = 0.2
raft_expansion = 1.5
raft_first_layer_density = 90%
raft_first_layer_expansion = 3
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 0
skirt_distance = 2
skirt_height = 2
skirts = 1
slice_closing_radius = 0.049
slicing_mode = regular
small_perimeter_speed = 30
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 80
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_bottom_contact_distance = 0
support_material_bottom_interface_layers = 0
support_material_buildplate_only = 0
support_material_closing_radius = 2
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.2
support_material_interface_speed = 80%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 50
support_material_style = grid
support_material_synchronize_layers = 0
support_material_threshold = 50
support_material_with_sheath = 0
support_material_xy_spacing = 60%
thick_bridges = 0
thin_walls = 0
threads = 4
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 40
top_solid_layers = 4
top_solid_min_thickness = 0.7
travel_speed = 180
travel_speed_z = 12
wall_distribution_count = 1
wall_transition_angle = 10
wall_transition_filter_deviation = 25%
wall_transition_length = 0.4
wipe_tower = 1
wipe_tower_bridging = 10
wipe_tower_brim_width = 5
wipe_tower_no_sparse_layers = 1
wipe_tower_rotation_angle = 329.682
wipe_tower_width = 60
wipe_tower_x = 149.263
wipe_tower_y = 206.771
xy_size_compensation = 0

[filament:Geeetech Mizar_M@PLA]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 100
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 60
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 25
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = ""
filament_soluble = 0
filament_spool_weight = 200
filament_toolchange_delay = 0
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = (Unknown)
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 205
full_fan_speed_layer = 2
inherits = 
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 20
slowdown_below_layer_time = 15
start_filament_gcode = "; Filament gcode\n"
temperature = 200

[printer:Geeetech Mizar_M@Gradient Color Module]
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,255x0,255x255,0x255
before_layer_gcode = G92 E0.0\n\n
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Prusament PLA"
default_print_profile = 0.15mm QUALITY @MK3
deretract_speed = 35,35
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM702 C\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM84 ; disable motors
extra_loading_move = -2
extruder_colour = #0000FF;#FF0080
extruder_offset = 0x0,0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = ;▩▩▩▩▩▩▩▩▩▩AFTER_LAYER_CHANGE# layer No：[layer_num] ———>Print Height：[layer_z] mm ▩▩▩▩▩▩▩▩▩▩\n
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 1000,1000
machine_max_acceleration_extruding = 1250,1250
machine_max_acceleration_retracting = 1250,1250
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 500,500
machine_max_acceleration_y = 500,500
machine_max_acceleration_z = 100,100
machine_max_feedrate_e = 1000,1000
machine_max_feedrate_x = 500,500
machine_max_feedrate_y = 500,500
machine_max_feedrate_z = 5,5
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.3,0.3
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.2,0.2
max_print_height = 260
min_layer_height = 0.1,0.1
nozzle_diameter = 0.4,0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host = 
printer_model = 
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_Geeetech\nPRINTER_MODEL_Mizar_M\n
printer_settings_id = Mizar M@Seperate Module
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 1
retract_before_travel = 3,3
retract_before_wipe = 15%,15%
retract_layer_change = 0,0
retract_length = 6,6
retract_length_toolchange = 0,0
retract_lift = 0,0
retract_lift_above = 0,0
retract_lift_below = 249,249
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 35,35
silent_mode = 1
single_extruder_multi_material = 0
start_gcode = M862.3 P "[printer_model]" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;Go outside print area\nG1 Z5.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X1 Y20 Z1.2 F5000 ; Move to start position\n; select extruder\nTc\n; Purge line\nG1 X1 Y200.0 Z1.2 F1500 E30 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X1.4 Y200.0 Z1.2 F5000 ; Move to side a little\nG1 X1.4 Y20 Z1.2 F1500 E30 ; Draw the second line\n\nM221 S{if layer_height<0.2}110{else}100{endif}\nG92 E0\n\nM163 S0 P1\nM163 S1 P0\nM164 S0  ;T0=100/0\nM163 S0 P0\nM163 S1 P1\nM164 S1  ;T1=0/100\nM163 S0 P0.5\nM163 S1 P0.5\nM164 S2  ;T2=50/50\nM166 A0 Z100 I0 J1 S1   ;Gradient Usage Instructions 1\n\n\n
template_custom_gcode = 
thumbnails = 
thumbnails_format = PNG
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
z_offset = 0

[printer:Geeetech Mizar_M@Separated color Module]
bed_custom_model = 
bed_custom_texture = 
bed_shape = 0x0,255x0,255x255,0x255
before_layer_gcode = G92 E0.0\n\n
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Prusament PLA"
default_print_profile = 0.15mm QUALITY @MK3
deretract_speed = 35,35
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+1, max_print_height)} F720 ; Move print head up{endif}\nG1 X0 Y210 F7200 ; park\n{if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+49, max_print_height)} F720 ; Move print head further up{endif}\nG1 E2 F5000\nG1 E2 F5500\nG1 E2 F6000\nG1 E-15 F5800\nG1 E-20 F5500\nG1 E10 F3000\nG1 E-10 F3100\nG1 E10 F3150\nG1 E-10 F3250\nG1 E10 F3300\n\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nM702 C\nG4 ; wait\nM221 S100 ; reset flow\nM900 K0 ; reset LA\n{if print_settings_id=~/.*(DETAIL @MK3|QUALITY @MK3|@0.25 nozzle MK3).*/}M907 E538 ; reset extruder motor current{endif}\nM104 S0 ; turn off temperature\nM84 ; disable motors
extra_loading_move = -2
extruder_colour = #0000FF;#FF0080
extruder_offset = 0x0,0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = ;▩▩▩▩▩▩▩▩▩▩AFTER_LAYER_CHANGE# layer No：[layer_num] ———>Print Height：[layer_z] mm ▩▩▩▩▩▩▩▩▩▩\n
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 1000,1000
machine_max_acceleration_extruding = 1250,1250
machine_max_acceleration_retracting = 1250,1250
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 500,500
machine_max_acceleration_y = 500,500
machine_max_acceleration_z = 100,100
machine_max_feedrate_e = 1000,1000
machine_max_feedrate_x = 500,500
machine_max_feedrate_y = 500,500
machine_max_feedrate_z = 5,5
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.3,0.3
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.2,0.2
max_print_height = 260
min_layer_height = 0.1,0.1
nozzle_diameter = 0.4,0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host = 
printer_model = 
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_Geeetech\nPRINTER_MODEL_Mizar_M\n
printer_settings_id = Mizar M@Seperate Module
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 1
retract_before_travel = 3,3
retract_before_wipe = 15%,15%
retract_layer_change = 0,0
retract_length = 6,6
retract_length_toolchange = 0,0
retract_lift = 0,0
retract_lift_above = 0,0
retract_lift_below = 249,249
retract_restart_extra = 0,0
retract_restart_extra_toolchange = 0,0
retract_speed = 35,35
silent_mode = 1
single_extruder_multi_material = 0
start_gcode = M862.3 P "[printer_model]" ; printer model check\nM862.1 P[nozzle_diameter] ; nozzle diameter check\nM115 U3.11.0 ; tell printer latest fw version\nG90 ; use absolute coordinates\nM83 ; extruder relative mode\nM104 S[first_layer_temperature] ; set extruder temp\nM140 S[first_layer_bed_temperature] ; set bed temp\nTx\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM109 S[first_layer_temperature] ; wait for extruder temp\nG28 W ; home all without mesh bed level\nG80 ; mesh bed leveling\n\n;Go outside print area\nG1 Z5.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed\nG1 X1 Y20 Z1.2 F5000 ; Move to start position\n; select extruder\nTc\n; Purge line\nG1 X1 Y200.0 Z1.2 F1500 E30 ; Draw the first line\nG92 E0 ; Reset Extruder\nG1 X1.4 Y200.0 Z1.2 F5000 ; Move to side a little\nG1 X1.4 Y20 Z1.2 F1500 E30 ; Draw the second line\n\nM221 S{if layer_height<0.2}110{else}100{endif}\nG92 E0\n\n\n
template_custom_gcode = 
thumbnails = 
thumbnails_format = PNG
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0,0
z_offset = 0

[physical_printer:Mizar M]
host_type = octoprint
preset_name = 
preset_names = 
print_host = 
printer_technology = FFF
printhost_apikey = 
printhost_authorization_type = key
printhost_cafile = 
printhost_password = 
printhost_port = 
printhost_ssl_ignore_revoke = 0
printhost_user = 

[presets]
print = Geeetech Mizar_M@Printing Set
sla_print = 
sla_material = 
printer = Geeetech Mizar_M@Separated color Module
filament = Geeetech Mizar_M@PLA
filament_1 = Geeetech Mizar_M@PLA
physical_printer =