Forgot your password?
No account?
Register one!
Please note the 3d touch can not use on printer M201 Rostock301 G2S G2 as the firmware do not support it.
3DTouch is an auto leveling sensor for 3D Printers that can precisely measure the tilt of your print surface. It can greatly improve the printing precision of your 3D Printer.
3DTouch features simple, smart and precise. It could work with nearly any kind of bed materials, such as glasses, woods, metals and so on.
The main functions and controls of 3DTouch are the same as most auto bed leveling sensors, which consists of a RC servo and a micro switch, thus, 3DTouch can be used on almost every 3D printer control board.
By using progressively designed solenoid and hall sensor, 3DTouch can integrate high precision in such a simple structure. To make it more user-friendly and to bring you more enjoyable printing experience we add many smart functions such as self-test, false alarm, alarm release and test mode for M119.
Features:
1 Simple
3DTouch can be easily applied, since it has a small and simple structure. Gathering information & firmware setting will be an easy task, because 3DTouch works as usual auto bed leveling sensor.
2 Smart
Self-test: The push pin is operated three times to test when the power is on
Alarm: The LED light blinks if a problem found on a self-test or on an operation
3 High-precision
3DTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise.
If you choose 3DTouch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience.
4. Innovative Solenoid: Ultra Power Saving
On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device.
Low power consumption even further drops joule heating, preventing from heat problem.
5 Technologies
3DTouch consists of Atmel ATtiny13A, solenoid, and a push pin.
6 wide Selection of Bed
3DTouch does not uses either optical, nor proximity (inductive/capacitive) sensor.
3DTouch is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely.
7 Optimized structure: Larger Build Size
3DTouch is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor.
3DTouch uses existing RC Servo motor signal intactly, so just plug 3DTouch on the same pins after removing servo motor.
3D touch auto leveling sensor is not plug_and_play; you will need to do some modification to your
firmware and for some control board,
you may need to do some soldering work to the connector. We have prepared the pins for you.
For detailed instructions, please refer to the user manual. If you need any help, please feel free to contact us.
For more detailed information, please refer to wiki
Specifications:
Voltage: 5V
Current: 15mA
Max. Current: 300mA
Cable length: 150mm
Net Weight: 10g
Shipping weight: 25g
Operate condition
3DTouch can be operated in the following condition.
One I/O for control (PWM or Software PWM)
One I/O for Z min (Z Probe)
GND and +5V power
Wiring
3-pin: Brown (-, GND), Red (+5V), Orange (control signal)
2-pin: Black (-, GND), White (Z min)
Caution
Additional power supply will be needed in case your board does not supply enough amperage.
Electronic devices can be damaged or even destroyed if connected to wrong polarity. [wrong terminal connect to 5V(+) and GND(-)]
Pulling/pushing hard on the push-pin can damage 3DTouch and make it less accurate.
Fix push-pin with locking paint after reassembling or adjusting core.
Do not remove or deform elastic material attached on the push-pin.
1 X 3DTouch Auto leveling sensor
1 X 3Pin Straight Pin
1 X 2Pin Straight Pin
2 X Screw & Nut & Washer
2 X Dupont Housing Shell 3Pin
2 X Dupont Housing Shell 2Pin
3 X Dupont Housing Shell 1Pin
14 X Dupont Terminal
1 X 10KΩ 1/8W Resistor
If I order this, is there anything else I need to order at the same time, screws bolts or extension cables.......anything??.??
no need
which printer you use?
Hi. Is it full compatible with Megatronics V2 and Repetier.
yes
I purchased a 3D Touch from you, I have wired and installed the product. It has caused my printer to run backwards so right goes left, up goes down and so on. The codes for operating the 3D Touch manually do not allow it to work but the light on the 3D Touch comes on so I know there is power to the unit. Help please.
Hello, you need upgrade to the latest firmware and set the configuration for the 3d touch in the firmware, if you do not set it, the print can not recognise the 3d touch
I ordered one of these from you, I am still waiting to receive it, when it comes in wich firmware do I install for a Prusa I3 Pro W ?
please use the latest version, thanks
Why is this $10 more when you add it to a printer package vs buying it separately?
Sorry, just promote this product this this week, it will recover the price as the same buy together with printer
Para que sirve la resistencia de 10k que viene en paquete junto al 3dtouch, no entiendo como no explican nada sobre ello.
Si può montare su una prusa i3 pro w? Se si bisogna effettuare modifiche a livello di firmware? Grazie
Yes, it can use on prow but you need upgrade the firmware and set it in the firmware
http://www.geeetech.com/forum/viewtopic.php?f=20&t=60826
Hi, my printer board is GT2560+4 A4988- is it fully compatible whith this board? Thanks
yes
I would like to buy one of this sensors for my Acrylic Geeetech Prusa I3 pro B 3D Printer with the GT2560 Rev A+ control board. Which firmware do I need to use this sensor with this board?
http://www.geeetech.com/forum/viewtopic.php?f=20&t=60826
I just bought the 3d Touch for an A10. My firmware is Marlin 1.1.8, is it ok or do i need to do something? Many thanks.
http://www.geeetech.com/forum/viewtopic.php?f=20&t=17046, please visit here, thanks
is fully compatible whit cr-10s and anet a8? the lenght of wire is ok? or i need a modify, where i buy it? the firmware of my printers are ok (all buy in october 2018) how i control it?
this can use on those printer but needb you to reinstall the firmware and setting, thanks
A10 first version (gt2560 rev B) work on it? Where i can find where to pin?
Firstly,please join Geeetech facebook user group,secondly,visit links:https://lookaside.fbsbx.com/file/Add%20BL%20Touch%20Sensor%20to%20A10.pdf?token=AWwpKGUP_KDb8zFpJuo8Wpn2BNyZdyntpJEC553t-7R0rVfusA2yJcEAoGB4RIoHPSfGnU29Gl4KFNDrUsZ1nXTs-1Orr6xk0fC0j5eAtUAO7wTy6MCiFOcItkiq9oLBWiVy-A-WeZUWB2tKHpgBofifOTLMVZR2-za5MDiArq08RQ
can i use it with a GT2560 V3.0 Control Board (A10)??
yes
Will it work on my Duplicator 5?
it need upgrade,otherwise, it can not use it
jsut finished installing a 3d touch auto bed leveling. scrolling through my LCD screen. i do not have a "BL self test"
which modles you use? have you set the configuration in the firmware?
unable to download manual
please leave your mails address here, will send you by mails,thanks
When printing 3dtouch does not pick up the stem. Marlin 1.1.9
The red light on? have you set configuration in the firmware of the 3 d touch?
a20m
it can use on A20M , thanks
will this work on a Geeeteck aliminium
it not support it, thanks
what mother boards will it work with
Does the Geeetech 3DTouch auto bed leveling sensor for 3D printer works with E180? And how to at it to the main board ?
E180 can not support auto leveling
Salve per collegarlo ad una stampante a10 serve fare unaggiornamento al sistema?
use the latest firmware, please
Should the aluminum"pin" move when I shake the unit lightly? I just opened the package and noticed it moves freely.
it need you power it then works , otherwise, it like that
Thank you for the quick reply, now I can install!
Does the Geeetech 3DTouch auto bed leveling sensor for 3D printer works with Anet A6?
it should works
How can I order the extension cables for this 3DTouch sensor?
Hi David, you can send mails to victory.lei@geeetech.cn, thanks
those wires look too short to reach the board on my pro w (gt2650 +) how do you connect it?
it need extension wire, thanks
Hello! :-) Is there any hint to use this sensor with a MKS Gen L board?
we do not sure if the sensor can use on this board as we do not have specification of such baord,thanks
Hello, is there a thingy I can print to mount the 3DTouch to the Geeetech A10? Or even detailed assembly instructions? I have bought both on Amazon recently.
The latest upgraded version A10 can support auto leveling, so please send me machine serial number, i will check for you
I have just sent you an email with all my details. I am loocking very forward to attach the 3DTouch to my Geeetech A10 already! :-)))
The latest upgraded version A10 can support auto leveling, so please send me machine serial number, i will check for you
Hello, bought A30 printer and on my printer there is only on 3 pin connector. I cannot connect the 3 + 2 pins connectors from 3Dtouch
please send me machine serial number? also send mails to jocelin.jia@geeetech.cn, thanks
Hi, how do attach this sensor to the new Geeetech A10M printer? Where do I attach the wires?
The connector should between extruder wheels, find the five pins and connect but you need upgrade the firmware firstly.
is there an stl file for a mount?
please join geeetech facebook user group, then post there,team support will send it to u
Any update on firmware update for the A10 so this can be used? Marlin 1.1.9 is installed on my A10
the firmware is testing, will support it in latest firmware
Hello, is it compatible with Geeetech A10 printer?
currently not support it, but we are upgrading the firmware.
Hello, I have purchased this for my M201 printer, but now your tech guys tell me there is no way to install it on the board. Is it true it works on the M201? why isn´t there any instrucctions on how to install it on a pdf document? if it doesnt work on the M201, will you return my money ? I have contacted the technical@geeetech.com and they dont provide any answer anymore.
Hello, thanks your feedback, for the M201,our firmware does not support the 3d touch,if you need use it, you need update the firmware by yourself. Also the delta printer can not use it. Do you got any suggestion before purchase?_ if yes, we can refund, otherwise,we can not,thanks
Sup friends, I have a 3DTouch sensor almost ready to work, but I fail to find where to plug the wires. Does anyone knows how I can deal with it ? I will need to send pictures though. Thank you in advance !
Hi Pir, Please email to jocelin.jia@geeetech.cn for help and show her picures,thanks.
how i can install 3d sensor on gtm32 board to m201? how firmware i can to use and wich link? where is the schema to install the sensor on gt2560 A+ too
HI Araken,you can contact to our tech by :technical@geeetech.com,thanks
So, will it work on a M201? the STM32 based printer
Hi I D, Yes,it works on M201 printer.Thanks.
hi is that one compatible with A30 printer ? is the firmware to be modified and how ? thanks
Hi It is not compatible with A30 printer at present.SKU:700-001-1079 this one is.
Can I use it in a Tronxy X5S(Main Board : cxy-v.2)?
does this mother board is marlin firware?
Hello, I have an Acrylic Geeetech Prusa I3 pro B, I recently bought the wifi module and I have a problem, my printer has the 3dtouch auto bed leveling and I do not know how to do the calibration. Apart from that, it has already happened to me 2 times that printing through the wifi module, the hotend stops heating and the printer keeps moving as if printing.
Hi Alberto,you can email more details about your problem to:victory.lei@geeetech.cn for help.Thanks.
Hello, I'm looking forward to buy an auto bed leveling sensor, I have seen this one and also this: http://www.geeetech.com/lj12a34zbx-npn-dc636v-inductive-proximity-sensor-switch-for-p-1024.html?zenid=ovnuaus6vt9hjhk4sh8cb06d52 . which one would you recommend this, or the other?
Hi Gustavo,sorry for late reply.This is auto leveling sensor.The other is a switch.Thanks
i can to install a m201? if no what is the prevision to upgrade
Hi areken,sorry for late reply.Yes,3D touch will help M201 auto leveling. Thanks
Hello I just got the 3D Touch and had issues, wrote to technical and got really fast answers and today we find out that I used the z max instead of z min connector so homing is working now which is great thanks a lot to the technician I'm not sure can I give the name to the public? Hope that I get help for auto bed leveling as well. Didn't aspect these good kind of support. Fred
Hi Fred ,thanks for your update here .any doubt pls kindly contact our tech for help ,they are very happy to help.
Hello I have installed the 3D Touch and modified the Firmware. but the 3D Touch don´t work. I need some help Please. Sorry for my terrible English :)
HI Michael ,you can contact to our tech by :technical@geeetech.com
Hello, I have the Pro B, and usin slic3r version 1.1.7 I've just recieved the 3DTouch. can you please tell me the configuration of slic3r to print the sensor mount. Thank you. Ramzi.
Hi Ramzi ,you can email to our tech:technical@geeetech.com for help .
ok thanks
I bought for this page, Order Confirmation No: 20171019141753678
Hi Miguel ,sorry for the delay as the 3d touch sensor we are more strict for the production ,and now just has stock ,will be shipped this 2 days ,do appreciate to your patient here.
When is the Shipping from order # 10602?
Hi Miguel , Where you buy ?As from website i cannot see the below order ,sorry that.
Hello. My sensor work fine in the middle of the bed and tree corner but don't stop at the last corner. Slicer is with G29. Sorry for my bad English.
Hi Gael ,could you pls email to our tech for help ? technical@geeetech.com
I have just purchased a "3d Touch leveling sensor" for a "GEEETECH i3 A Pro the one with 3 in 1 controller". Can you help me with some information on the wiring and software re-configuration please.
Hi Nejad ,you can email to our tech for help:technical@geeetech.com
Hi there did you get the "3d Touch leveling sensor" working on your GEEETECH i3 as I have just finished building my own?
Hi ,you can check about our manual by :https://www.geeetech.com/Documents/3DTouch%20auto%20leveling%20sensor%20%20User%20Manual.rar ,also if you have any problem you can email to our tech:technical@geeetech.com for help.
I'm a newbie to 3D printing and I've just bought the 3DTouch sensor for my Pro B. I need to know what I have to do to my Pro B to get the sensor to work and is there any on line drawings which show or explain which wire of the sensor goes to which ever pin on the control board.
Hi Charlie ,you can download the manual here:https://www.geeetech.com/Documents/3DTouch%20auto%20leveling%20sensor%20%20User%20Manual.rar,there have many details ,also if you still have problem you can email to our technican for help :technical@geeetech.com
Hello, I have the Geeetech Prusa I3 pro B and buy the 3DTouch auto bed leveling but I can not configure Arduino to make it work. Can you load Marlin already configured for 3D Touch? Thank you
Hi Miguel ,Could you pls email to our technican to send the marlin to you by email:technical@geeetech.com
Hi I have a M201 some time ago the control failed on it so i fitted a Radds control that i was given. I have purchased a 3dTouch can you give me an idea on the wiring for the 3dtouch and a radds control. Regards Martin
Hi Martin,thank you for reaching,sorry that the 3d touch sensor just can support by GT2560 ,the M201 is GTM32 ,so cannot .Pls note with thank.
I have a BQ Prusa i3 hephestos xl with firmware 2.51. The firmware is in HEX format and does not open with Arduino. After three weeks of exhaustion, the only one who managed to find that Arduino can open is a Merlin 1.4.2 but the folder "Configuration.h" does not exist.. I only find "Configurationstore.h".. Before I throw it all away, can you help me find the right firmware for my printer? I'm practical of electronics, but being able to run this malicious object is not everyone...
Hi Mauro ,could you pls check with the printer manufacturer whether the printer can support BL touch or not ?As our technican not fimilar with this printer ,sorry that.
Hello, i have a geeetech mecreator 2, could you lease send me the firmware file and special settings to modify for auto levelling please? There is only setting for the Prusa I3 pro B, pro C and pro X in your dowloadable documentation just above. Thanks, regards,
Hi Olivier,sorry that currently the 3d touch sensor just can be used on pro B and pro X and pro W ,for those prusa i3 series .Pls note with thank.
There is something worng with my 3d touch i asked you're sales department for a replacement but they are not responding... wich is not nice it is joust not working and you're technical department can't help me because they can't figure out whats wrong, so please can i get a new one because like i said THIS ONE IS NOT WORKING !!!
HI Andro,Thank you for reaching us ,could you pls tell me where are you bought the sensor ?And you also emailed to our technican for help ?
hi ihave sent an email but thought would msg on here for a quicker reply, i have the 3d touch auto leveller but the wire is too short to reach the control board could you tell me where i could get the correct extender cable for it please. thanks
Hi Stuart ,i have sent an email to you ,pls check.
Hi, is the 3D Touch sensor supported by the 3-in-1 Control Box with the ribbon cables between the box and the connector board on the chassis? I have the Aluminum Prusa I3 with Sanguinololu which I want to upgrade with the control box and 3D Touch sensor. Thanks David
Hi David,for the 3d touch just can be compatiable with the GT2560 controller . For the Aluminum prusa i3 you can buy a 3 in 1 control box to upgrade it.
Hi David ,pls email your problem by detail to our technican:technical@geeetech.com
My replies don't seem to be getting through. Anyway, what I mean is: HOW do I do it? Where do the connectors go? What are the firmware changes?
Hi Paul ,you can list your problem by detail to our technican for help:technical@geeetech.com
I have the Pro C (dual extruders) and the GT2560 Rev A+ board (with the 3 extra pins). Can I use them for the 3D Touch, AND keep my Z Min connection ? It's just in case the sensor fails.
Hi Paul ,you can try ,for the pro C is much difficult for the 3d touch sensor.
Have installed your 3d touch sensor on my new 3d printer. Sometimes it accidentally pulls down while printing. What can cause this issue? Using marlin firmware, mks gen v1.4 board. Have heat bed installed.
Hi Alex,pls email to our technican for help:technical@geeetech.com
I have the same problem. :(
Hi Maciej ,could you pls email to our tech for help ? technical@geeetech.com
Thank you for all your help on my installation of this auto level. The instructions on the Wiki are adequate and I am up and running.
Hello Justin,that sounds great.
hi there when you show how to setup the configuration h and the H pins you show pins for ultimaker could you tell me what do you change in the h pins for the ramps 1.4 board please
Hi Alexander ,pls email to our technican for help:technical@geeetech.com
Here you're the support for the pro C with metal carrier for dual extruders: http://www.thingiverse.com/thing:2187522
Hi Zina would you please have a look at my configuration H file to see where i am going wrong as said in my other comment i am a newbie and at 66years young the old grey matter is not up to the job could you help
HI Alexander ,thank you for reaching us.You can list your problem by detail to our technican for help :technical@geeetech.com
Hello Geeetech I purchased a Geeetech 3DTouch auto bed leveling sensor and put it up on my i3 Pro B according to user manual v. 2.0, everything seems to work but the Nozzen is around 5mm above bed. I have corrected Marlin as described for GT2560 Rev A + (#define SERVO0_PIN 11 // 13 // untested). What's missing here ?? Greeting Aage
Hi Aage,could you pls list you problem by details to our technican :technical@geeetech.com he will check and give some help.Thanks.
Hello, Please tell me where I need to install the sensor, and what holder and where exactly?
Hello Sandra ,you can check the detail on the manual :https://www.geeetech.com/Documents/3DTouch%20auto%20leveling%20sensor%20%20User%20Manual%20version2.0.zip if you still have problem pls feel free to email to our technican :technical@geeetech.com
How to connect this sensor to Geeetech prusa I3 A Pro 3D? The needed connection pins are not on the GT box control board!
hi ,pls email to our technican to help:technical@geeetech.com
When this will be available for M201 printer with GTM32pro board ?
Hi Cico,sorry that this cannot use for the M201 printer.
Hi Justin,here is the manual you can check it:https://www.geeetech.com/Documents/3DTouch%20auto%20leveling%20sensor%20%20User%20Manual%20version2.0.zip
I have the I3 Pro B, and am just trying to check out the software before I purchase the leveler. I can't find all the indicated information in the software change depicted in instructions. Thanks
Can't find the reference to "pins-h" in the firmware installation. Seems to be missing in my software. How do I get that?
Hi Justin,could you pls list your detail to my email and tell me which printer you are :zina.luo@geeetech.cn
Hi, sorry if double post (first seems not to be posted) I ordered this kit for my Geeetech prusa I3 pro B black Acrylic, and after few issues it works very well !! Now, I would like to add a filament cooling fan, is it possible with the auto leveling sensor ? If ok, do you have any advice / link fan support to print Many thanks in advance Bertrand
Hello Bertrand ,it's ok.For the cooling fan our technican said logically can add one more ,you can search more detail on thingiverse.
Hello. Does it fit the M201 ? Many thanks
Hello Aurelie,sorry that the M201 cannot support the 3D touch sensor .
Hi i bougth i3 pro b with the gt2560 rev a, and the 3dtouch auto bed, but my board dont have the wired conection, what can i do? thanks
Hello ,the gt2560 rev a board have no wired connection ,need to solder by yourself,you can check the manual here:https://www.geeetech.com/Documents/3DTouch%20auto%20leveling%20sensor%20%20User%20Manual%20version2.0.zip
Greetings Geeetech! This auto levelling sensor looks compatible with the Delta Rostock G2S Pro - Is it? Also, how sensitive/gentle is it? The inbuilt auto levelling probe on the G2S pro has too much resistance and can tilt the spider/effector when making contact during auto-levelling, which can change the auto-levelling results. Is this probe softer so it will not make the spider/effector tilt with pressure when auto-levelling?
Hello Ross, sorry that the G2S printer cannot support the 3D touch sensor.Pls note with thank.
Please help me, my printer Geetech prusa i3 pro B take probe only from middle of the print table !! How do i set up to take probe from all four corners of the table ?! thx
Hello Alin,have you check the manual ? if you still can not sovle the problem you can emial to our techncian for help:technical@geeetech.com
Hi, how long the connection wires, it takes the extensions
It depends on the distance between the nozzle to the main board.
I have a geetech aluminum I3 and I see in the comments that it will work if I have a certain board? I don't mind changing the board if I can have the censor and still have the display work. What board would I need?
Hi,sounds great that you have one on your pro X ,but sorry that the Me creator2 printer cant support the 3D touch .
Hi. will this one work with the Me Creator 2? ive already have the i3 pro X and im really happy with it.
If any one needs one on one support let me know, because whats your time worth?. georges3dprinters.com
Won't allow me to pay for item on PayPal.
Hi Randy ,what happened to the paypal payment? The website accept the paypal payment.
Will this work on your Geeetech Prusa I3 X? Thanks in advance.
Hello David, Yes, this can be used on pro X, Please watch the video here https://www.youtube.com/watch?v=7aav0i5cOL4&feature=youtu.be
I have the Pro C dual extruder, if the same mount is the same as the pro B, how do I attach it when its where the fan is? or do I attach it against the fan?
Yes, you can mount it against the fan!
Hello Roger , you can print this one http://www.thingiverse.com/thing:1769822
After printing a mount for the sensor (for the pro C), it seems that this is not the same as for the pro B. The gap between the holes is not the same, and the fan is at the same place. Where can I find the right support?
I bought this package and it doesn't come with the extension wires to reach theboard . It's not much help without them. Can you recommend somewhere to get the extension wires?
Hello George, thanks for contacting us, please send your enquiry to sales@geeetech.com, our sales will help you.
I have a Geeetech i3 pro x, will this fit my machine. My machine works like the previous machine.
yes, this works perfectly on the pro B
Hi, is the M201 printer compatible with this device?
Hello, I am sorry to tell you this item is not compatible with M201 now
Hi I'm having a little trouble with the 3D Touch. Please see here http://www.geeetech.com/forum/viewtopic.php?f=27&t=18496&p=34314#p34314 Any suggestions?
I have a hictop diy reprap prusa i3 with the Mks Base V1.3 Reprap Arduino board can I use this on my unit?
3-pin: Brown (-, GND) Red (+5V) Orange (control signal) 2-pin: Black (-, GND) White (Z min) can you find spare pins for the above wires?
Yes it looks like I can, attach it to the board. next question is about the programing, I have not see it on this printer yet, so I am a little concerned.
Hi There, is the Geeetech prusa I3 A Pro supported and how to wire the sensor. I have purchase the sensor but figure out Z min has only 2 pins ?
yes, there is only 2 pin on the board. but you can find the 3-pin in the package of the sensor. please refer to the user manual of the sensor for the wiring
Hi,I bought I3 pro C in July2015.Board is GT2560.Is this board support 3DTouch auto leveling sensor?is it need aluminum heatbed?how to connect and what is sensing distance? thanks Shiva
yes,,GT2560 support 3DTouch auto leveling sensor. You do need to add aluminum plate, glass also works. please refer to the user manual and download the sensor mount, then, everything will be easy.
Would this work with the Geeetech Aluminum Prusa I3? I have the Sanguinololu +4A4988 board.
yes, but if you add it to the Sanguinololu board, you can not use the LCD anymore cause the pin will be occupied
In the manual you write: "Step1. Remove the Z max connector from the board and replace it with a 3Pin Straight Pin. You need to use soldering iron here." The Z-max connection on my board (Prusa I3 Pro B latest edition of a couple of weeks old) only has a 2-pin. How can I replace that with a 3-pin? Before I decide buy this sensor I would like to know for sure I can fit it easily.
yes, there is only 2 pin for the Z max, that's why we need to replace it.We will send you the 3 pin Straight Pin, please check the package list for this sensor
Can i use the leveling Sensor with the MeCreator 2?
yes, you can use it with the MeCreator 2.
Is there a Manual for the MeCreator2? Because the Z Axis drives down and not up when i use G28/G29
just a question how long does it take for you techs to get back with me, its been 3 days now?
have you contacted them?
Yes I have, I have sent them 2 emails now.
I have a hictop diy reprap prusa i3 with the Mks Base V1.3 Reprap Arduino board can I use this on my unit?
Hello Levi, can you send a picture of the board to technical@geeetech.com. Please also confirm with the manufacture whether the board has enough I/O pins
can this be used on with the Prusa I3 pro b i purchased about 5 weeks ago?
Hello George Yes, surely it cam be used on your pro B. You can check the video here https://www.youtube.com/watch?v=DxAVV_8r3p4
With the 3DTouch was also a 10k resistor. For what I need this Resistor?
For some board u will need it to increase the electrical level. what is your control board please?
I use the GT2560 control board
I´m missing a answer :-(
I have still no answer, I think, you will not answer my question - Need I the resistor also for the GT2560 Control board?
Hi, does this work with G2S pro ?
yes, we will update the instructions soon
Save: 15% off
TERMS OF USE
HELP CENTER
COMPANY INFORMATION
MEMBER AREA