0

Your Shopping Cart is empty.

  • XBee Pro 63mW U.FL Connection-Series 2(ZigBee Mesh) S2B
    • i i
    • images/l/Geeetech_XBEES2BUFL_1.jpg images/l/Geeetech_XBEES2BUFL_1.jpg
    • images/l/Geeetech_XBEES2BUFL_2.jpg images/l/Geeetech_XBEES2BUFL_2.jpg
    • images/l/Geeetech_XBEES2BUFL_3.jpg images/l/Geeetech_XBEES2BUFL_3.jpg
    • images/l/Geeetech_XBEES2BUFL_4.jpg images/l/Geeetech_XBEES2BUFL_4.jpg
XBee Pro 63mW U.FL Connection-Series 2(ZigBee Mesh) S2B
INFO

SKU:700-001-0721

Shipping Weight:70g

Free Shipping!

$59.50
Qty:
VS
VOTES

Vote for specials.

0 votes

maker-moments

This is the XBee XBP24-BZ7UIT-004 module from Digi. The new Series 2B improves upon the power output and data protocol of the Pro Series2. Series 2B modules allow you to create complex mesh networks based on the XBee ZB mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
Series 2B modules use a different hardware configuration from the earlier models and while they will communicate with Series 2 XBee modules, they are not compatible with the outdated Series 2.5 Modules.

 

Regular VS Pro

There are a few differences between the regular XBees and the XBee Pros. The Pros are a bit longer, use more power. The greater power means longer range (1 mile instead of 300ft) so if you need the range then use the Pros, otherwise stick with the regular models. You can mix and match these on the same network.

Note: If you are looking for a simple point-to-point configuration, you might want to try the Series 1 instead. The Series 2 requires considerable setup and configuration.
Note: Series 1 and Series 2B XBee modules have the same pin-out. However, Series 1 modules cannot communicate with Series 2B modules.
Note: If you are using these outside, please check with your local laws regarding radio communication.

 

Performance

RF Data Rate:250 Kbps

Indoor/Urban Range:    300 ft. (90 m)   

Outdoor/RF Line-of-Sight Range:    2 miles (3200 m)/ Int’l 5000 ft (1500 m)

Transmit Power:63 mW (+18 dBm) / Int’l 10 mW (+10 dBm)

Receiver Sensitivity (1% PER): -102 dBm

 

Features

Adjustable Power: Yes

I/O Interface:3.3V CMOS UART, SPI, I2C, PWM, DIO, ADC

Configuration Method:API or AT commands, local or over-the-air

Frequency Band:2.4 GHz

Interference Immunity:DSSS (Direct Sequence Spread Spectrum)

Serial Data Rate:1200 bps - 1 Mbps

ADC Inputs:(4) 10-bit ADC inputs

Digital I/O:10

Operating Temperature & Humidity: -40° C to +85° C, 0-95% humidity non-condensing

 

Programmability

Memory: N/A   

CPU/Clock Speed:N/A  

 

Networking & Security

Encryption: 128-bit AES

Reliable Packet Delivery: Retries/Acknowledgments

IDs and Channels: PAN ID, 64-bit IEEE MAC, 15 channels

 

Power Requirements

Supply Voltage: 2.7 - 3.6VDC

Transmit Current:  205 mA

Receive Current:    47 mA

Power-Down Current:  3.5 uA @ 25º C

Physical Properties

Weight: 3.6g

Size: 3.3cm x 2.5cm

Antenna: U.FL

For more information, please kindly check at this page.

 

Documents:

Digi XBee Series 2B Page

Datasheet

Dimensional Drawings

Digi Examples and Guides

login or register to add your words.