Difference between revisions of "433Mhz RF link kit"

From Geeetech Wiki
Jump to: navigation, search
(examlple code)
(How to buy)
 
(15 intermediate revisions by the same user not shown)
Line 1: Line 1:
  
 
== Introduction  ==
 
== Introduction  ==
The kit is consisted of transmitter and receiver, popular used for remote control.
 
  
 +
The kit is consisted of transmitter and receiver, popular used for remote control.
 +
 +
[[File:Rf1.jpg|600px]]
  
 
== Specification  ==
 
== Specification  ==
Line 12: Line 14:
  
 
== Wiring diagram ==
 
== Wiring diagram ==
 +
[[File:Wiring111.jpg]]
  
 
+
==examlple code==
= examlple code =
 
 
Transmmiter:
 
Transmmiter:
  
Line 62: Line 64:
 
     uint8_t buf[VW_MAX_MESSAGE_LEN];
 
     uint8_t buf[VW_MAX_MESSAGE_LEN];
 
     uint8_t buflen = VW_MAX_MESSAGE_LEN;
 
     uint8_t buflen = VW_MAX_MESSAGE_LEN;
     if (vw_get_message(buf, &buflen)) // Non-blocking
+
     if (vw_get_message(buf, &buflen))//Non-blocking
    {
+
  {
int i;
+
    int i;
        digitalWrite(12, true);// Flash a light to show received good message
+
    digitalWrite(12, true); //Flash a light to show received good message
// Message with a good checksum received, dump it.
+
    Serial.print("Got: "); //Message with a good checksum received, dump it.
Serial.print("Got: ");
+
    for (i = 0; i < buflen; i++)
for (i = 0; i < buflen; i++)
+
  {
{
+
    Serial.print(buf[i], HEX);
    Serial.print(buf[i], HEX);
+
    Serial.print(" ");
    Serial.print(" ");
+
    }
}
+
    Serial.println("");
Serial.println("");
+
    digitalWrite(12, false);
        digitalWrite(12, false);
 
 
     }
 
     }
}
+
    }
 +
 
 +
==How to buy==
 +
Click here to buy [http://www.geeetech.com/433mhz-rf-link-kit-p-160.html 433Mhz RF link kit]

Latest revision as of 03:19, 29 May 2012

Introduction

The kit is consisted of transmitter and receiver, popular used for remote control.

Rf1.jpg

Specification

  • Frequency: 433Mhz.
  • Modulation: ASK
  • Receiver Data Output: High - 1/2 Vcc, Low - 0.7v
  • Transmitter Input Voltage: 3-12V (high voltage = more transmitting power)

Wiring diagram

Wiring111.jpg

examlple code

Transmmiter:

#include <VirtualWire.h>
#undef int
#undef abs
#undef double
#undef float
#undef round
void setup()
{
   Serial.begin(9600);	  // Debugging only
   Serial.println("setup");
   // Initialise the IO and ISR
   vw_set_ptt_inverted(true); // Required for DR3100
   vw_setup(2000);	 // Bits per sec
}
void loop()
{
   const char *msg = "hello";
   digitalWrite(13, true); // Flash a light to show transmitting
   vw_send((uint8_t *)msg, strlen(msg));
   vw_wait_tx(); // Wait until the whole message is gone
   digitalWrite(13, false);
   delay(200);
}

Receiver:

#include <VirtualWire.h>
#undef int
#undef abs
#undef double
#undef float
#undef round
void setup()
{
   Serial.begin(9600);	// Debugging only
   Serial.println("setup");
   // Initialise the IO and ISR
   vw_set_ptt_inverted(true); // Required for DR3100
   vw_setup(2000);	 // Bits per sec
   vw_rx_start();       // Start the receiver PLL running
}
void loop()
{
   uint8_t buf[VW_MAX_MESSAGE_LEN];
   uint8_t buflen = VW_MAX_MESSAGE_LEN;
   if (vw_get_message(buf, &buflen))//Non-blocking
  {	
   int i;
   digitalWrite(12, true);  //Flash a light to show received good message
   Serial.print("Got: "); //Message with a good checksum received, dump it.
   for (i = 0; i < buflen; i++)
  {
   Serial.print(buf[i], HEX);
   Serial.print(" ");
    }
   Serial.println("");
   digitalWrite(12, false);
   }
   }

How to buy

Click here to buy 433Mhz RF link kit