Me Creator 2

AcoVanConis
Posts: 3
Joined: Thu Dec 08, 2016 4:44 am

Re: Me Creator 2

Post by AcoVanConis » Sun Apr 09, 2017 12:56 am

Hi John
where is this menu item, in Repetier host I cannot find him
have the same issue, the print is not centered, a litte bit too left
tnx
You have to use the Display and Knob from the Printer.

8ung
Posts: 17
Joined: Thu Feb 23, 2017 2:08 am

Re: Me Creator 2

Post by 8ung » Sun Apr 09, 2017 2:10 am

Thanks works perfect
did a leveiling test http://www.thingiverse.com/thing:34558
and its exact in the middle now
Last edited by 8ung on Thu Apr 13, 2017 6:18 pm, edited 1 time in total.

8ung
Posts: 17
Joined: Thu Feb 23, 2017 2:08 am

Re: Me Creator 2

Post by 8ung » Wed Apr 12, 2017 3:31 am

BTW I have to do the reset procedure every startup, is there a way to store it permanent?
tnx

User avatar
William
Site Admin
Posts: 4466
Joined: Tue Jun 07, 2016 9:38 am

Re: Me Creator 2

Post by William » Thu Apr 13, 2017 11:19 am

Hi,8ung
you can find it in LCD main menu:Control>Store memory.Just the attachment shows.
Attachments
1.png
1.png (209.72 KiB) Viewed 3947 times
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

ejo
Posts: 6
Joined: Sun Apr 09, 2017 9:11 pm

Re: Me Creator 2

Post by ejo » Mon May 01, 2017 8:39 pm

My Z gets stuck on ~150mm for no clear reason. Max height should be 160mm, but when it hits that certain point, it won't move up or down anymore. If I tell bed to go up and same time help the lead screw by turning it gently, it starts to move again.

I haven't actually printed anything that tall, I did just test it to make sure what actual height limit is.

8ung
Posts: 17
Joined: Thu Feb 23, 2017 2:08 am

Re: Me Creator 2

Post by 8ung » Thu May 04, 2017 3:27 pm

William wrote:Hi,8ung
you can find it in LCD main menu:Control>Store memory.Just the attachment shows.
tnx William it worked
kr

ejo
Posts: 6
Joined: Sun Apr 09, 2017 9:11 pm

Re: Me Creator 2

Post by ejo » Sat May 06, 2017 1:38 am

Two stepper drivers were adjusted to 0.87v and two to 1.13v. I guess motors are the same model, so I did adjust them all to ~1.1v. This didn't help the Z problem. The drivers are not labeled, so I'm not sure which is for which motor.

It is hard to measure, but I think leadscrew is tilted less than millimeter to left. This makes it too tight bed to go all the way down I cannot see a way to tilt it back, construction is too solid.

I did try to loosen various screws and loosening the part that connects bed to lead screw did help a little bit. Now it gets stuck ~158mm and I think I can safely print up to 155mm which is close enough. I did set Cura to 150mm height and only increase it if absolutely necessary.

But I still think this should have been noticed in quality check. You did print a square with this very printer, but didn't bother to check Z height?

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests