How to upload firmware for GTM32 Pro board?

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: The Restock 301(STM32 Pro Board) Firmware Burning Steps

Post by William » Sat Oct 15, 2016 9:17 am

Make sure the Baud Rate and the COM port are all right.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

User avatar
Lami René
Posts: 195
Joined: Mon Sep 26, 2016 6:47 pm
Location: Sherbrooke, Québec, Canada

Re: The Restock 301(STM32 Pro Board) Firmware Burning Steps

Post by Lami René » Sat Oct 15, 2016 10:00 am

Bonjour raoulito9 et William Kwok,

Quel doit-être la vitesse et les autres paramètres pour la communication sur le port COM ?

Sur la carte STM32 Pro, est-ce qu'il n'y aurait pas un cavalier "jumper" a mettre ou a enlever pour permettre la gravure du micrologiciel "firmware" ?

Cordialement,

L'ami René
Un pour tous et tous pour un !
One for all and all for one !
-------------------------------------
Mon imprimante modifié : http://forums.reprap.org/read.php?178,781375,781375
Voir aussi pour mes pièces : https://www.thingiverse.com/thing:2464177

User avatar
Lami René
Posts: 195
Joined: Mon Sep 26, 2016 6:47 pm
Location: Sherbrooke, Québec, Canada

Re: The Restock 301(STM32 Pro Board) Firmware Burning Steps

Post by Lami René » Sat Oct 15, 2016 11:18 am

Rebonjour raoulito9 et William Kwok,

Je viens de tomber sur cette page "flashing_rumba_bootloader" :

https://www.nova-labs.org/wiki/3d_print ... bootloader

Il y a peut-être une solution qui fonctionnera pour vous !

Cordialement,

L'ami René
Un pour tous et tous pour un !
One for all and all for one !
-------------------------------------
Mon imprimante modifié : http://forums.reprap.org/read.php?178,781375,781375
Voir aussi pour mes pièces : https://www.thingiverse.com/thing:2464177

raoulito9
Posts: 42
Joined: Mon Sep 05, 2016 3:24 am

Re: The Restock 301(STM32 Pro Board) Firmware Burning Steps

Post by raoulito9 » Sat Oct 15, 2016 4:35 pm

Hi this is ok, i found how to flash the new firmware.
If you look at my screenshots, you'll see my printer is connected : correct com port and correct baud rate...
I just missed a little step aof the tuto, bad documented :
When you are connected into hyperterminal, first push C key with the disconnect icon THEN some new chinese chars appears THEN PRESS 1 KEY.... I missed the step of pressing the 1 key before sending the file....
And it is while examining the screenchot of the tuto i found it....

Please, document it better....and add the sentence of pressing the 1 key to your tuto...

Flash is done on my printer , and absolutely no difference for me.

Please release the source codes for this printer.
You all know open source firmware are waYYYYYY better han all you could ever imagine.

Have a good day.

ISURU
Posts: 5
Joined: Mon Oct 31, 2016 4:53 pm

Re: How to upload firmware for Rostock 301(GTM32 Pro board)?

Post by ISURU » Mon Oct 31, 2016 5:01 pm

HI could anybody please help me to upgrade the firmware version on my Rostock 301
I did everything as explained above.
at last i got a message saying "jump app fail!"

and my lcd screen got stuck.
The Nob/push button doesn`t work.
restarted but still same.

how do I reset? the mother board

thx for any help

ISURU
Posts: 5
Joined: Mon Oct 31, 2016 4:53 pm

Re: How to upload firmware for Rostock 301(GTM32 Pro board)?

Post by ISURU » Mon Oct 31, 2016 5:05 pm

This is the message i had at the end of upload.
LCD display stopped working.
try to upload the firmware again doesn`t work.
Attachments
2.jpg
2.jpg (77.95 KiB) Viewed 35215 times

User avatar
William
Site Admin
Posts: 6340
Joined: Tue Jun 07, 2016 9:38 am

Re: How to upload firmware for Rostock 301(GTM32 Pro board)?

Post by William » Mon Oct 31, 2016 5:27 pm

Maybe you missed something?You'd better check if there is something different from the post in your procedure.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

ISURU
Posts: 5
Joined: Mon Oct 31, 2016 4:53 pm

Re: How to upload firmware for Rostock 301(GTM32 Pro board)?

Post by ISURU » Mon Oct 31, 2016 7:08 pm

i have travel several times it doesn`t work.

User avatar
Lami René
Posts: 195
Joined: Mon Sep 26, 2016 6:47 pm
Location: Sherbrooke, Québec, Canada

Re: How to upload firmware for Rostock 301(GTM32 Pro board)?

Post by Lami René » Mon Nov 14, 2016 9:24 am

Bonjour,

Quand Geeetech va fournir la procédure pour la mise à jour sous Linux Kubuntu du micrologiciel "Firmeware" pour l'imprimante Rostock 301 et de la carte contrôleur GTM32 Pro ?

Est-ce que Geeetech a des personnes compétentes pour réalise ce travaille ou est-ce que Geeetech est trop pauvre pour embaucher et payer les personnes compétentes et respecter sa parole écrite sur son site Web qui dit « Operating system: Windows/Mac/Linux » ?

Ma version du micrologiciel installer d'usine est 1.1.0 A.

Cordialement,

L'ami René
Un pour tous et tous pour un !
One for all and all for one !
-------------------------------------
Mon imprimante modifié : http://forums.reprap.org/read.php?178,781375,781375
Voir aussi pour mes pièces : https://www.thingiverse.com/thing:2464177

User avatar
Lami René
Posts: 195
Joined: Mon Sep 26, 2016 6:47 pm
Location: Sherbrooke, Québec, Canada

Re: How to upload firmware for Rostock 301(GTM32 Pro board)?

Post by Lami René » Mon Nov 14, 2016 10:30 am

Rebonjour,

En cherchant une solution pour la procédure pour la mise à jour sous Linux Kubuntu du micrologiciel "Firmeware" pour l'imprimante Rostock 301 et de sa carte contrôleur GTM32 Pro, j'ai trouvé dans les dépôts standard de Linux Kubuntu 16.04 64 bits en français le logiciel "CuteCom" (voir le clip-écran).

Je pense que vos techniciens pourraient utiliser ce logiciel pour nous indiquer la configuration et les détails de la procédure à suivre pour graver la dernière version du micrologiciel "Firmeware" pour l'imprimante Rostock 301 et de la carte contrôleur GTM32 Pro sous Linux et respecter son engagement de fournir une solution pour les ordinateurs avec Linux.

Si vos techniciens n'ont as les compétences pour le logiciel CuteCom, en standard sous Linux Kubuntu il y aussi les logiciels Arduino et Moserial, si vos techniciens ont plus de compétence avec ces deux derniers logiciels.

Est-ce que Geeetech a de l'honneur et donne de l'importance à ses clients ?

Nous le verrons très prochainement de la manière qu'ils vont traiter la présente suggestion et les nouvelles solutions avec ces trois logiciels différents !

Cordialement,

L'ami René
P.-s. J'ai l'imprimante depuis le 27 octobre 2016 et je n'ai toujours rien imprimé avec, car Geeetech ne donne pas les solutions à nos problèmes...
Attachments
CuteCom Linux Kubuntu 16.04 64 bits.png
Clip-écran du logiciel CuteCom sous Linux Kubuntu 16.04 64 bits
CuteCom Linux Kubuntu 16.04 64 bits.png (39 KiB) Viewed 35163 times
Un pour tous et tous pour un !
One for all and all for one !
-------------------------------------
Mon imprimante modifié : http://forums.reprap.org/read.php?178,781375,781375
Voir aussi pour mes pièces : https://www.thingiverse.com/thing:2464177

Post Reply