Z AXIS BLOCKED in one direction

User avatar
William
Site Admin
Posts: 4336
Joined: Tue Jun 07, 2016 9:38 am

Re: Z AXIS BLOCKED in one direction

Post by William » Mon Oct 10, 2016 5:17 pm

Then plug Z motors into X/Y motor's slot on the board to see how Z motors go.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Pierfrancesco
Posts: 13
Joined: Thu Oct 06, 2016 3:37 pm

Re: Z AXIS BLOCKED in one direction

Post by Pierfrancesco » Mon Oct 10, 2016 6:21 pm

Yes... In X,Y slots Z motors works fine... Separatly but in both direction

Pierfrancesco
Posts: 13
Joined: Thu Oct 06, 2016 3:37 pm

Re: Z AXIS BLOCKED in one direction

Post by Pierfrancesco » Tue Oct 11, 2016 3:08 pm

I think that the board is defected, how Can I get another One ?

User avatar
William
Site Admin
Posts: 4336
Joined: Tue Jun 07, 2016 9:38 am

Re: Z AXIS BLOCKED in one direction

Post by William » Tue Oct 11, 2016 4:11 pm

Hi,
Take some clear photos of your board's back and front,i wanna see if there is a bad soldering at the "DIR" pin of Z axis.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Pierfrancesco
Posts: 13
Joined: Thu Oct 06, 2016 3:37 pm

Re: Z AXIS BLOCKED in one direction

Post by Pierfrancesco » Wed Oct 12, 2016 12:59 am

Image

Image

User avatar
William
Site Admin
Posts: 4336
Joined: Tue Jun 07, 2016 9:38 am

Re: Z AXIS BLOCKED in one direction

Post by William » Wed Oct 12, 2016 5:24 pm

Pierfrancesco wrote:Image

Image
You can try soldering this spot in the picture again if you have a tool.
2560.jpg
2560.jpg (58.04 KiB) Viewed 4273 times
PS.Did you try reflashing the firmware for Pro B?
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Pierfrancesco
Posts: 13
Joined: Thu Oct 06, 2016 3:37 pm

Re: Z AXIS BLOCKED in one direction

Post by Pierfrancesco » Wed Oct 12, 2016 5:45 pm

I will try to solder... Yes, I reflashed firmware many times

Pierfrancesco
Posts: 13
Joined: Thu Oct 06, 2016 3:37 pm

Re: Z AXIS BLOCKED in one direction

Post by Pierfrancesco » Wed Oct 12, 2016 9:26 pm

Nothing happened, always the same... :(

User avatar
William
Site Admin
Posts: 4336
Joined: Tue Jun 07, 2016 9:38 am

Re: Z AXIS BLOCKED in one direction

Post by William » Sat Oct 15, 2016 4:28 pm

Try the new board when it arrives,and update this post plz.
-Keep your mind and try to test it. :)
-Everything will be fun!-Support all Getech printer.
-You can ask me the questions and I will kindly reply.
-Respect others is the best way you can get help!

Pierfrancesco
Posts: 13
Joined: Thu Oct 06, 2016 3:37 pm

Re: Z AXIS BLOCKED in one direction

Post by Pierfrancesco » Sat Oct 15, 2016 4:35 pm

Thank you man :)

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests