Both extruders on i3 pro C dual extruder not working

Post Reply
redwezel
Posts: 4
Joined: Sun Jul 05, 2015 9:24 pm

Both extruders on i3 pro C dual extruder not working

Post by redwezel » Tue Jul 07, 2015 6:53 am

I have tried most things mentioned. The motors are good and run on z position. Have the temperature at 200c and still nothing. Support gave me a firmware file for single extruder I3 pro b that did not work either.could it be the ramp? or the gt2650? or firmware? :?:

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by Sherry » Tue Jul 07, 2015 9:24 am

hi,your printer type is i3 pro C,dual extruder.why use the firmware for single extruder I3 pro b.Please burn the right firmware(refer th the attachment).
Attachments
PI3B-GT2560-dual extruder.rar
(268.96 KiB) Downloaded 220 times

redwezel
Posts: 4
Joined: Sun Jul 05, 2015 9:24 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by redwezel » Wed Jul 08, 2015 8:37 am

Ok, I am trying to upload it and this is what I am getting
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_getsync(): timeout communicating with programmer

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by Sherry » Wed Jul 08, 2015 2:45 pm

could you leave the skype.

redwezel
Posts: 4
Joined: Sun Jul 05, 2015 9:24 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by redwezel » Thu Jul 09, 2015 9:56 am

Eric wrote:could you leave the skype.
what?

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by Sherry » Thu Jul 09, 2015 5:32 pm

i mean your contact information,please tell me your email or skype.Following information display that the firmware goes wrong.For further troubleshooting,please contact me via email or skype.this is my email address:sherry.li@geeetech.cn.
avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_getsync(): timeout communicating with programmer

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by Sherry » Thu Jul 09, 2015 5:47 pm

avrdude: stk500v2_ReceiveMessage(): timeout
avrdude: stk500v2_getsync(): timeout communicating with programmer

it means that you do not burn the firmware successfully.Please turn on the power(PSU) when you burn the firmware.There are too many electronics components on the control board ,so it need more power to burn the firmware.

agilliam
Posts: 8
Joined: Mon Jun 22, 2015 9:20 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by agilliam » Sun Jul 12, 2015 2:35 am

There is an obvious problem, I too have a PRO C with dual extruders, and neither extruder works correctly. I have the GT2560 Rev A as well, and 2 stepper controllers were dead, replaced with drv8825 and set it to 1/16 step and it still doesn't work. Tested on ramps 1.4 and they work fine. The GT2560 has A LOT of bad solder joints (at least mine does). The foreign trade manager is aware, the new firmware she sent me still does not work. I need a working FIRMWARE!

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by Sherry » Mon Jul 13, 2015 10:27 am

my apology for delay in responding,the updated firmware is in the attachment.

Sherry
Posts: 362
Joined: Wed Jul 01, 2015 12:52 pm

Re: Both extruders on i3 pro C dual extruder not working

Post by Sherry » Mon Jul 13, 2015 10:28 am

my apology for delay in responding,the updated firmware is in the attachment.
Attachments
GT_I3_pro_C.zip
(283.1 KiB) Downloaded 225 times

Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests